HP Latex 800 Introductory Information - Page 5

Fire hazard, Mechanical hazard - w printer

Get HP Latex 800 PDF manuals and user guides View all HP Latex 800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

● Do not touch the internal enclosures of the printer's curing zones. ● Let the printer cool down before accessing the print zone and output platen in the case of a substrate jam. ● Let the printer cool down before performing some maintenance operations. Fire hazard The curing subsystems of the printer operate at high temperatures. To avoid the risk of fire, take the following precautions: ● The customer is responsible for meeting the printer's requirements and the Electrical Code requirements according to the local jurisdiction of the country where the equipment is installed. Use the power supply voltage specified on the nameplate. ● Connect the power cord to a dedicated line protected by a branch circuit breaker, as explained in the site preparation guide. Do not use a power strip (relocatable power tap) to connect both power cords. ● Use only the power cord supplied by HP with the printer. Do not use a damaged power cord. Do not use the power cord with other products. ● Do not insert objects through slots in the printer. ● Take care not to spill liquid on the printer. After cleaning, make sure all components are dry before using the printer again. ● Do not use aerosol products that contain flammable gases inside or around the printer. Do not operate the printer in an explosive atmosphere. ● Do not block or cover the openings of the printer. ● Do not attempt to dismantle or modify the curing modules. ● Ensure that the operating temperature of the substrate, as recommended by its manufacturer, is not exceeded. If this information is not available, ask the manufacturer. Do not load substrates that cannot be used at an operating temperature above (257°F). ● Do not load substrates with auto-ignition temperatures below (482°F). If this information is not available, printing must be supervised at all times. See note below. NOTE: Test method based on EN ISO 6942:2002: Evaluation of materials and material assemblies when exposed to a source of radiant heat, method B. The test conditions to determine the temperature when the substrate starts ignition (either flame or glow) were: Heat flux density: 30 kW/m², copper calorimeter, K-type thermocouple. Mechanical hazard The printer has moving parts that could cause injury. To avoid personal injury, take the following precautions when working close to the printer: ● Keep your clothing and all parts of your body away from the printer's moving parts. ● Avoid wearing necklaces, bracelets, and other hanging objects. ENWW Safety precautions 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
●
Do not touch the internal enclosures of the printer’s curing zones.
●
Let the printer cool down before accessing the print zone and output platen in the
case of a substrate jam.
●
Let the printer cool down before performing some maintenance operations.
Fire hazard
The curing subsystems of the printer operate at high temperatures.
To avoid the risk of
fi
re, take the following precautions:
●
The customer is responsible for meeting the printer’s requirements and the Electrical
Code requirements according to the local jurisdiction of the country where the
equipment is installed. Use the power supply voltage speci
fi
ed on the nameplate.
●
Connect the power cord to a dedicated line protected by a branch circuit breaker, as
explained in the site preparation guide. Do not use a power strip (relocatable power
tap) to connect both power cords.
●
Use only the power cord supplied by HP with the printer. Do not use a damaged
power cord. Do not use the power cord with other products.
●
Do not insert objects through slots in the printer.
●
Take care not to spill liquid on the printer. After cleaning, make sure all components
are dry before using the printer again.
●
Do not use aerosol products that contain
fl
ammable gases inside or around the
printer. Do not operate the printer in an explosive atmosphere.
●
Do not block or cover the openings of the printer.
●
Do not attempt to dismantle or modify the curing modules.
●
Ensure that the operating temperature of the substrate, as recommended by its
manufacturer, is not exceeded. If this information is not available, ask the
manufacturer. Do not load substrates that cannot be used at an operating
temperature above (257°F).
●
Do not load substrates with auto-ignition temperatures below (482°F). If this
information is not available, printing must be supervised at all times. See note below.
NOTE:
Test method based on EN ISO 6942:2002: Evaluation of materials and material
assemblies when exposed to a source of radiant heat, method B. The test conditions to
determine the temperature when the substrate starts ignition (either
fl
ame or glow) were:
Heat
fl
ux density: 30 kW/m², copper calorimeter, K-type thermocouple.
Mechanical hazard
The printer has moving parts that could cause injury. To avoid personal injury, take the
following precautions when working close to the printer:
●
Keep your clothing and all parts of your body away from the printer’s moving parts.
●
Avoid wearing necklaces, bracelets, and other hanging objects.
ENWW
Safety precautions
3