HP Mini 1125NR HP Mini 1000 Netbook - Maintenance and Service Guide - Page 46

of the drive is attached., to which the USB board pass-through cable that lies across the top

Get HP Mini 1125NR PDF manuals and user guides View all HP Mini 1125NR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

4. Remove the two Phillips PM2.0×4.5 screws (3) that secure the hard drive to the device. Then lift the drive (4) up, and slide it out of the drive bay. Reverse this procedure to install the hard drive. To remove the solid-state drive: 1. Release the ZIF connector (1) to which the USB board pass-through cable (that lies across the top of the drive) is attached. 2. Disconnect the USB board pass-through cable (2), and then detach the tape from the top of the drive. 3. Release the LIF connector (1) to which the solid-state drive cable is attached, and then disconnect the cable (2). 38 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
4.
Remove the two Phillips PM2.0×4.5 screws
(3)
that secure the hard drive to the device. Then lift
the drive
(4)
up, and slide it out of the drive bay.
Reverse this procedure to install the hard drive.
To remove the solid-state drive:
1.
Release the ZIF connector
(1)
to which the USB board pass-through cable (that lies across the top
of the drive) is attached.
2.
Disconnect the USB board pass-through cable
(2)
, and then detach the tape from the top of the
drive.
3.
Release the LIF connector
(1)
to which the solid-state drive cable is attached, and then disconnect
the cable
(2)
.
38
Chapter 4
Removal and replacement procedures