HP NC326m HP ProLiant Network Adapter Scripting Utility User Guide - Page 11

Configuration properties, Adapter configuration properties for Windows Server 2008, Server 2008

Get HP NC326m - PCI Express Dual Port Gigabit Server Adapter PDF manuals and user guides View all HP NC326m manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Configuration properties Adapter configuration properties for Windows Server 2008 The following properties are configured on the target server adapters from the source server data. Each adapter property displays only if the property is supported by the selected adapter. • PriorityVLANTag-Enables or disables the ability to insert or remove the 802.1q tags for priority and VLAN. • JumboPacket-The size in bytes of the largest supported Jumbo Packet (an Ethernet frame that is greater than 1514 bytes) that the hardware can support. • RSSEnabled-Enables dynamic load balancing of incoming traffic across CPUs. • IPChecksumOffloadIPv4-Describes whether the device enabled or disabled the calculation of IPv4 checksums. • TCPChecksumOffloadIPv4-Describes whether the device enabled or disabled the calculation of TCP Checksum over IPv4 packets. • UDPChecksumOffloadIPv4-Describes whether the device enabled or disabled the calculation of UDP checksum over IPv4 packets. • TCPUDPChecksumOffloadIPv4-Describes whether the device enabled or disabled the calculation of TCP or UDP checksum over IPv4 packets. If this TCP/UDP Checksum Offload (IPv4) property is present, it overrides and disables the TCP Checksum Offload (IPv4), UDP Checksum Offload (IPv4), and IPv4 Checksum Offload properties. • TCPChecksumOffloadIPv6-Describes whether the device enabled or disabled the calculation of TCP checksum over IPv6 packets. • UDPChecksumOffloadIPv6-Describes whether the device enabled or disabled the calculation of UDP checksum over IPv6 packets. • TCPUDPChecksumOffloadIPv6-Describes whether the device enabled or disabled the calculation of TCP or UDP checksum over IPv4 packets. If this TCP/UDP Checksum Offload (IPv6) property is present, it overrides and disables the TCP Checksum Offload (IPv6), UDP Checksum Offload (IPv6), and IPv6 Checksum Offload properties. • LSOV1IPv4-Describes whether the device enabled or disabled the segmentation of large TCP packets over IPv4 for large send offload version 1 (LSOv1). • LSOV2IPv4-Describes whether the device enabled or disabled the segmentation of large TCP packets over IPv4 for large send offload version 2 (LSOv2). • LSOV2IPv6-Describes whether the device enabled or disabled the segmentation of large TCP packets over IPv6 for large send offload version 2 (LSOv2). Configuration properties 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
Configuration properties 11
Configuration properties
Adapter configuration properties for Windows
Server 2008
The following properties are configured on the target server adapters from the source server data.
Each adapter property displays only if the property is supported by the selected adapter.
•
PriorityVLANTag
—Enables or disables the ability to insert or remove the 802.1q tags for priority and
VLAN.
•
JumboPacket
—The size in bytes of the largest supported Jumbo Packet (an Ethernet frame that is
greater than 1514 bytes) that the hardware can support.
•
RSSEnabled
—Enables dynamic load balancing of incoming traffic across CPUs.
•
IPChecksumOffloadIPv4
—Describes whether the device enabled or disabled the calculation of IPv4
checksums.
•
TCPChecksumOffloadIPv4
—Describes whether the device enabled or disabled the calculation of TCP
Checksum over IPv4 packets.
•
UDPChecksumOffloadIPv4
—Describes whether the device enabled or disabled the calculation of
UDP checksum over IPv4 packets.
•
TCPUDPChecksumOffloadIPv4
—Describes whether the device enabled or disabled the calculation of
TCP or UDP checksum over IPv4 packets. If this TCP/UDP Checksum Offload (IPv4) property is
present, it overrides and disables the TCP Checksum Offload (IPv4), UDP Checksum Offload (IPv4),
and IPv4 Checksum Offload properties.
•
TCPChecksumOffloadIPv6
—Describes whether the device enabled or disabled the calculation of TCP
checksum over IPv6 packets.
•
UDPChecksumOffloadIPv6
—Describes whether the device enabled or disabled the calculation of
UDP checksum over IPv6 packets.
•
TCPUDPChecksumOffloadIPv6
—Describes whether the device enabled or disabled the calculation of
TCP or UDP checksum over IPv4 packets. If this TCP/UDP Checksum Offload (IPv6) property is
present, it overrides and disables the TCP Checksum Offload (IPv6), UDP Checksum Offload (IPv6),
and IPv6 Checksum Offload properties.
•
LSOV1IPv4
—Describes whether the device enabled or disabled the segmentation of large TCP
packets over IPv4 for large send offload version 1 (LSOv1).
•
LSOV2IPv4
—Describes whether the device enabled or disabled the segmentation of large TCP
packets over IPv4 for large send offload version 2 (LSOv2).
•
LSOV2IPv6
—Describes whether the device enabled or disabled the segmentation of large TCP
packets over IPv6 for large send offload version 2 (LSOv2).