HP P5389A hp server tc3100 operation and maintenance guide (English, v1.1) - Page 67

Navigator CD-ROM. To do this, insert the Navigator CD-ROM, Failed to load Microcode Update

Get HP P5389A - Intel Pentium III-S 1.4 GHz Processor Upgrade PDF manuals and user guides
UPC - 088698513354
View all HP P5389A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Chapter 5 Error Messages Code 0901 0A00 0B0x 0B1x 0B2x Description Integrated LAN enable error Display refresh rate error Missing Microcode Update Failed to load Microcode Update Defective Microcode Update Problem/Solution The system could not enable the integrated LAN. To correct this: 1. Reset the Integrated LAN by powering off the HP Server. 2. Disconnect the power cord for 20 seconds. 3. Reconnect the power cord and power on the HP Server. 4. If the error appears upon restarting, update the system BIOS. 5. Insert the HP Navigator CD-ROM in the CD-ROM drive and power-cycle your system. This will initialize the flash utility on the HP Navigator CDROM. 6. If the error persists, the system board may need to be replaced. Contact your service representative. The parameters returned by the display do not match the DDC standard used by the server for automatic setup of ergonomic refresh rates. To correct this: 1. Disable the 'Plug & Play Display' feature in the Setup Utility to avoid a blank or unreadable screen at power-up. 2. Use the Setup Utility to manually set the video refresh rates to the highest ergonomic refresh rates supported by the display. Refer to display monitor's User's Guide for specifications. Your system is missing the Microcode Update data block for the microprocessor. Your must correct this problem to avoid possible malfunction or reliability problems. To correct this: 1. Update your BIOS by running the flash utility from you Navigator CD-ROM. To do this, insert the Navigator CD-ROM in the CD-ROM drive and power-cycle your system. 2. If updating your BIOS does not clear this error, contact your service representative. Your system has failed to load the Microcode Update data block for the microprocessor. Your must correct this problem to avoid possible malfunction or reliability problems. To correct this: 1. Update your BIOS by running the flash utility from you Navigator CD-ROM. To do this, insert the Navigator CD-ROM in the CD-ROM drive and power-cycle your system. 2. If updating your BIOS does not clear this error, contact your service representative. The Microcode Update data block for the microprocessor is defective. To correct this: 1. Update your BIOS by running the flash utility from you Navigator CD-ROM. To do this, insert the Navigator CD-ROM in the CD-ROM drive and power-cycle your system. 2. If updating your BIOS does not clear this error, contact your service representative. 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
Chapter 5
Error Messages
61
Code
Description
Problem/Solution
0901
Integrated LAN enable error
The system could not enable the integrated LAN.
To correct this:
1.
Reset the Integrated LAN by powering off the HP Server.
2.
Disconnect the power cord for 20 seconds.
3.
Reconnect the power cord and power on the HP Server.
4.
If the error appears upon restarting, update the system BIOS.
5. Insert the
HP Navigator CD-ROM
in the CD-ROM drive and
power-cycle your system.
This will initialize the flash utility on the
HP Navigator CD-
ROM
.
6.
If the error persists, the system board may need to be replaced.
Contact your service representative.
0A00
Display refresh rate error
The parameters returned by the display do not match the DDC
standard used by the server for automatic setup of ergonomic refresh
rates.
To correct this:
1.
Disable the 'Plug & Play Display' feature in the Setup Utility to
avoid a blank or unreadable screen at power-up.
2.
Use the Setup Utility to manually set the video refresh rates to
the highest ergonomic refresh rates supported by the display.
Refer to display monitor's User's Guide for specifications.
0B0x
Missing Microcode Update
Your system is missing the Microcode Update data block for the
microprocessor.
Your must correct this problem to avoid possible malfunction or
reliability problems.
To correct this:
1.
Update your BIOS by running the flash utility from you
Navigator CD-ROM. To do this, insert the Navigator CD-ROM
in the CD-ROM drive and power-cycle your system.
2.
If updating your BIOS does not clear this error, contact your
service representative.
0B1x
Failed to load Microcode Update
Your system has failed to load the Microcode Update data block for
the microprocessor.
Your must correct this problem to avoid possible malfunction or
reliability problems.
To correct this:
1.
Update your BIOS by running the flash utility from you
Navigator CD-ROM. To do this, insert the Navigator CD-ROM
in the CD-ROM drive and power-cycle your system.
2.
If updating your BIOS does not clear this error, contact your
service representative.
0B2x
Defective Microcode Update
The Microcode Update data block for the microprocessor is defective.
To correct this:
1.
Update your BIOS by running the flash utility from you
Navigator CD-ROM. To do this, insert the Navigator CD-ROM
in the CD-ROM drive and power-cycle your system.
2.
If updating your BIOS does not clear this error, contact your
service representative.