HP Pavilion dm4-2000 HP Pavilion dm4 Entertainment PC - Maintenance and Servic - Page 81

Lift the right side of the system board

Get HP Pavilion dm4-2000 PDF manuals and user guides View all HP Pavilion dm4-2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

i. Power connector cable (see Power connector cable on page 66) j. Bluetooth module (see Bluetooth module on page 68) 1. Turn the computer upright with the left side toward you. 2. Disconnect the optical drive connector cable (1) from the system board. 3. Remove the three Phillips M2.5×5.0 screws (2) that secure the system board to the computer. 4. Loosen the captive screw in the fan sink that secures the system board (3). 5. Lift the right side of the system board (4). 6. Release the system board by sliding it to the right at an angle (5) until the connectors on the left side of the system board clear the base enclosure, and then remove the system board. Reverse the preceding procedure to install the system board. Component replacement procedures 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
i.
Power connector cable (see
Power connector cable
on page
66
)
j.
Bluetooth module (see
Bluetooth module
on page
68
)
1.
Turn the computer upright with the left side toward you.
2.
Disconnect the optical drive connector cable
(1)
from the system board.
3.
Remove the three Phillips M2.5×5.0 screws
(2)
that secure the system board to the computer.
4.
Loosen the captive screw in the fan sink that secures the system board
(3)
.
5.
Lift the right side of the system board
(4)
.
6.
Release the system board by sliding it to the right at an angle
(5)
until the connectors on the left
side of the system board clear the base enclosure, and then remove the system board.
Reverse the preceding procedure to install the system board.
Component replacement procedures
73