HP ProLiant WS460c HP Service Pack for ProLiant Quick Start Guide - Page 9

Initiating deployment, Online mode

Get HP ProLiant WS460c PDF manuals and user guides View all HP ProLiant WS460c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

The following table describes TPM detection scenarios that you might encounter. Scenario Result If TPM is detected and enabled, the installation is not silent, A warning message appears. Select OK to continue. The and a system ROM must be updated. installation is not canceled. If TPM is detected and enabled, the installation is silent, the /tpmbypass switch is not given, and any firmware updated must be applied to the server. No warning appears. A new log file is generated (%systemdrive%\cpqsystem\log\cpqstub.log). Because the installation is silent, the installation is terminated and cannot continue. If TPM is detected and enabled with Option ROM A warning message appears. After selecting OK, you can Measuring, the installation is not silent, and a system ROM continue. The installation is not canceled. must be updated. If TPM is detected and enabled with Option ROM Measuring, the installation is silent, the /tpmbypass switch is not given, and any firmware updated must be applied to the server. No warning appears. A new log file is generated (%systemdrive%\cpqsystem\log\cpqstub.log). Because the installation is silent, the installation is terminated and cannot continue. If TPM is detected and enabled, the installation is silent, the installation occurs, and the /tpmbypass switch is supplied. The installation occurs. Initiating deployment Use the HP SUM GUI to deploy SPP components in online or offline interactive modes to local or remote hosts. For detailed instructions and prerequisites see the HP Smart Update Manager User Guide at http://www.hp.com/go/hpsum/documentation for the appropriate version of HP SUM. Online mode To initiate deployment in online mode: 1. Copy the SPP to a USB thumb drive, hard drive, or file system. For instructions, see "SPP staging procedures" (page 11). 2. Launch HP SUM from the root of the ISO: • Windows: \hp\swpackages\hpsum.exe • Linux: /hp/swpackages/hpsum TIP: If you are updating only firmware or software, use a filter argument: • /romonly - With this filter switch, HP SUM only displays firmware components needed for installation. • /softwareonly - With this filter switch, HP SUM only displays software components needed for installation. 3. To review the EULA, locate Start.htm in the root of the ISO and open it in one of the supported browsers. 4. Follow the instructions on the screen. Offline mode To initiate deployment in offline mode: 1. Copy the SPP to a USB thumb drive, hard drive, or file system. When using a USB thumb drive, the ISO must be bootable. For instructions, see "SPP staging procedures" (page 11). 2. Boot the server to the SPP. Using HP SUM to deploy an SPP 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
The following table describes TPM detection scenarios that you might encounter.
Result
Scenario
A warning message appears. Select
OK
to continue. The
installation is not canceled.
If TPM is detected and enabled, the installation is not silent,
and a system ROM must be updated.
No warning appears. A new log file is generated
(%systemdrive%\cpqsystem\log\cpqstub.log
).
If TPM is detected and enabled, the installation is silent,
the
/tpmbypass
switch is not given, and any firmware
updated must be applied to the server.
Because the installation is silent, the installation is
terminated and cannot continue.
A warning message appears. After selecting
OK
, you can
continue. The installation is not canceled.
If TPM is detected and enabled with Option ROM
Measuring, the installation is not silent, and a system ROM
must be updated.
No warning appears. A new log file is generated
(
%systemdrive%\cpqsystem\log\cpqstub.log
).
If TPM is detected and enabled with Option ROM
Measuring, the installation is silent, the
/tpmbypass
Because the installation is silent, the installation is
terminated and cannot continue.
switch is not given, and any firmware updated must be
applied to the server.
The installation occurs.
If TPM is detected and enabled, the installation is silent,
the installation occurs, and the
/tpmbypass
switch is
supplied.
Initiating deployment
Use the HP SUM GUI to deploy SPP components in online or offline interactive modes to local or
remote hosts. For detailed instructions and prerequisites see the
HP Smart Update Manager User
Guide
at
h
t
tp://w
w
w
.hp
.co
m/go/hp
sum/doc
ume
n
t
ati
o
n
for the appropriate version of HP SUM.
Online mode
To initiate deployment in online mode:
1.
Copy the SPP to a USB thumb drive, hard drive, or file system. For instructions, see
“SPP
staging procedures” (page 11)
.
2.
Launch HP SUM from the root of the ISO:
•
Windows:
\hp\swpackages\hpsum.exe
•
Linux:
/hp/swpackages/hpsum
TIP:
If you are updating only firmware or software, use a filter argument:
•
/romonly
— With this filter switch, HP SUM only displays firmware components needed
for installation.
•
/softwareonly
— With this filter switch, HP SUM only displays software components
needed for installation.
3.
To review the EULA, locate
Start.htm
in the root of the ISO and open it in one of the
supported browsers.
4.
Follow the instructions on the screen.
Offline mode
To initiate deployment in offline mode:
1.
Copy the SPP to a USB thumb drive, hard drive, or file system. When using a USB thumb
drive, the ISO must be bootable. For instructions, see
“SPP staging procedures” (page 11)
.
2.
Boot the server to the SPP.
Using HP SUM to deploy an SPP
9