HP SignagePlayer mp8000s Maintenance & Service Guide: HP SignagePlayer mp8 - Page 135

Hood Sensor,

Get HP SignagePlayer mp8000s PDF manuals and user guides View all HP SignagePlayer mp8000s manuals
Add to My Manuals
Save this manual to your list of manuals

Page 135 highlights

5. From the outside of the chassis, remove the four Phillips screws that secure the fan to the chassis, then from the inside of the chassis, slide the fan forward and lift it up and out of the chassis. Figure 7-37 Removing the rear fan To install the rear fan, reverse the removal procedure. Hood Sensor 1. Prepare the computer for disassembly (Preparation for Disassembly on page 92). 2. Remove the computer access panel (Computer Access Panel on page 99). 3. Remove the optical drive (Removing the Existing Optical Drive on page 107). 4. Unplug the hood sensor cable from the white system board connector labeled HSENSE and remove the cable from the white clip mounted on the inside chassis wall. 5. Slide the hood sensor into the chassis to remove it from its slot. Figure 7-38 Removing the hood sensor To install the hood sensor, reverse the removal procedures. Hood Sensor 125

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
5.
From the outside of the chassis, remove the four Phillips screws that secure the fan to the chassis,
then from the inside of the chassis, slide the fan forward and lift it up and out of the chassis.
Figure 7-37
Removing the rear fan
To install the rear fan, reverse the removal procedure.
Hood Sensor
1.
Prepare the computer for disassembly (
Preparation for Disassembly
on page
92
).
2.
Remove the computer access panel (
Computer Access Panel
on page
99
).
3.
Remove the optical drive (
Removing the Existing Optical Drive
on page
107
).
4.
Unplug the hood sensor cable from the white system board connector labeled HSENSE and
remove the cable from the white clip mounted on the inside chassis wall.
5.
Slide the hood sensor into the chassis to remove it from its slot.
Figure 7-38
Removing the hood sensor
To install the hood sensor, reverse the removal procedures.
Hood Sensor
125