HP StorageWorks 2/64 HP StorageWorks Fabric OS 5.x Advanced Web Tools Administ - Page 42

Enabling insistent domain ID mode (FICON only), Con Fabric, Apply, Insistent Domain ID Mode

Get HP StorageWorks 2/64 - Core Switch PDF manuals and user guides View all HP StorageWorks 2/64 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Figure 9 Configure tab, Fabric subtab Configuring fabric parameters 1. Launch the Switch Admin module as described on page 36. 2. Disable the switch as described in "Enabling and disabling a switch" on page 39. 3. Click the Configure tab. 4. Click the Fabric subtab. 5. Make the fabric parameter configuration changes. 6. Click Apply. 7. Enable the switch as described in "Enabling and disabling a switch" on page 39. Enabling insistent domain ID mode (FICON only) When insistent domain ID (ID_ID) mode is enabled, the current domain setting for the switch is insistent; that is, the same ID is requested during switch reboots, power cycles, CP failovers, firmware downloads, and fabric reconfigurations. If the fabric does not assign the insistent domain ID, the switch segments from the fabric. This parameter is for use with FICON only. 1. Launch the Switch Admin module as described on page 36. 2. Disable the switch as described in "Enabling and disabling a switch" on page 39. 3. Click the Configure tab. 4. Click the Fabric subtab. 5. Check the Insistent Domain ID Mode check box. 6. Click Apply. 7. Enable the switch as described in "Enabling and disabling a switch" on page 39. 42 Managing your fabrics, switches, and ports

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
42
Managing your fabrics, switches, and ports
Figure 9
Configure tab, Fabric subtab
Configuring fabric parameters
1.
Launch the Switch Admin module as described on
page 36
.
2.
Disable the switch as described in ”
Enabling and disabling a switch
” on page 39.
3.
Click the
Configure
tab.
4.
Click the
Fabric
subtab.
5.
Make the fabric parameter configuration changes.
6.
Click
Apply
.
7.
Enable the switch as described in ”
Enabling and disabling a switch
” on page 39.
Enabling insistent domain ID mode (FICON only)
When insistent domain ID (ID_ID) mode is enabled, the current domain setting for the switch is insistent;
that is, the same ID is requested during switch reboots, power cycles, CP failovers, firmware downloads,
and fabric reconfigurations. If the fabric does not assign the insistent domain ID, the switch segments from
the fabric.
This parameter is for use with FICON only.
1.
Launch the Switch Admin module as described on
page 36
.
2.
Disable the switch as described in ”
Enabling and disabling a switch
” on page 39.
3.
Click the
Configure
tab.
4.
Click the
Fabric
subtab.
5.
Check the
Insistent Domain ID Mode
check box.
6.
Click
Apply
.
7.
Enable the switch as described in ”
Enabling and disabling a switch
” on page 39.