HP StorageWorks 2/64 HP StorageWorks Fabric OS 5.x Advanced Web Tools Administ - Page 75

Administering extended fabrics, About extended link buffer allocation

Get HP StorageWorks 2/64 - Core Switch PDF manuals and user guides View all HP StorageWorks 2/64 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

7 Administering extended fabrics This chapter contains the following information: • About extended link buffer allocation, page 75 • Configuring for long distance, page 76 About extended link buffer allocation As the distance between switches and the link speed increases, additional buffer-to-buffer credits are required to maintain maximum performance. The number of credits reserved for a port depends on the switch model and on the extended ISL mode for which it is configured. The Extended Fabric tab of the Switch Admin module displays information about the port speed, long-distance setting, and buffer credits, as shown in Figure 24. Use this tab to configure the long-distance setting of a port. For detailed information on managing extended fabrics, see the HP StorageWorks Fabric OS 5.x administrator guide. The Extended Fabric tab provides the following information: • Port Number • Buffer Limited: A buffer-limited port can come online with fewer buffer credits allocated than its configuration specifies, allowing it to operate at a reduced bandwidth instead of being disabled for lack of buffers. Buffer-limited operation is supported for the L0 and LD extended ISL modes only and is persistent across reboots, switch disabling and enabling, and port disabling and enabling. • Port Speed, which is displayed as follows: • 1G 1 Gbit/sec • 2G 2 Gbit/sec • 4G 4 Gbit/sec • N1 Negotiated 1 Gbit/sec • N2 Negotiated 2 Gbit/sec • N4Negotiated 4 Gbit/sec • Auto-Negotiation • Buffer Needed/Allocated: The number of buffers needed and the number of buffers that are actually allocated. • Actual Distance: The actual distance, in kilometers, for the link. • Desired Distance: Required for a port configured in LD mode (see Table 9), the desired distance, in kilometers, for the link. This value is the upper limit for calculating buffer availability for the port. If the measured distance is more than the specified desired distance, the port is allocated the number of buffers required by the specified desired distance. • Long Distance: Table 9 describes the long-distance settings and identifies which settings require an Extended Fabrics license. Fabric OS 5.x Advanced Web Tools administrator guide 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
Fabric OS 5.x Advanced Web Tools administrator guide
75
7
Administering extended fabrics
This chapter contains the following information:
•
About extended link buffer allocation
, page 75
•
Configuring for long distance
, page 76
About extended link buffer allocation
As the distance between switches and the link speed increases, additional buffer-to-buffer credits are
required to maintain maximum performance. The number of credits reserved for a port depends on the
switch model and on the extended ISL mode for which it is configured.
The Extended Fabric tab of the Switch Admin module displays information about the port speed,
long-distance setting, and buffer credits, as shown in
Figure 24
. Use this tab to configure the
long-distance setting of a port. For detailed information on managing extended fabrics, see the
HP
StorageWorks Fabric OS 5.x administrator guide
.
The Extended Fabric tab provides the following information:
•
Port Number
•
Buffer Limited: A buffer-limited port can come online with fewer buffer credits allocated than its
configuration specifies, allowing it to operate at a reduced bandwidth instead of being disabled for
lack of buffers.
Buffer-limited operation is supported for the L0 and LD extended ISL modes only and is persistent
across reboots, switch disabling and enabling, and port disabling and enabling.
•
Port Speed, which is displayed as follows:
•
1G 1 Gbit/sec
•
2G 2 Gbit/sec
•
4G 4 Gbit/sec
•
N1 Negotiated 1 Gbit/sec
•
N2 Negotiated 2 Gbit/sec
•
N4Negotiated 4 Gbit/sec
•
Auto-Negotiation
•
Buffer Needed/Allocated: The number of buffers needed and the number of buffers that are actually
allocated.
•
Actual Distance: The actual distance, in kilometers, for the link.
•
Desired Distance: Required for a port configured in LD mode (see
Table 9
), the desired distance, in
kilometers, for the link. This value is the upper limit for calculating buffer availability for the port. If the
measured distance is more than the specified desired distance, the port is allocated the number of
buffers required by the specified desired distance.
•
Long Distance:
Table 9
describes the long-distance settings and identifies which settings require an
Extended Fabrics license.