HP Visualize c3000 hp Visualize b1000 and c3000 workstations service handbook - Page 143

Installing Memory Cards, Removing Memory

Page 143 highlights

Figure 4-57. Installing Memory Cards Notches Field Replaceable Units FRU Removal and Replacement Press down on ejector tabs to open Step 1 them and place the DIMM card in the connector so that your fingers are on the edge of the DIMM card. Step 2 Black Ejector Tab Push the DIMM card down firmly and evenly into the connector to be sure it is properly seated. White Ejector Tab 7. Place the DIMM card in the connector, lining it up with the guides. Make sure to put the notched end toward the white ejector tab (to the left). See Figure 4-57. 8. Close the ejector tab. 9. Press firmly and evenly on the DIMM card to ensure that it seats properly. The ejector tabs engage when the DIMM is properly seated. 10.Replace the power supply and workstation left side panel. You may now plug the power cord back in to the electrical outlet. 11.Verify that this installation was successful by following the steps in Chapter 6, "The Boot Console Handler." If you have only replaced a faulty DIMM, you must execute the pdt clear command in the service menu of the Boot Console Handler. Answer yes (Y) to the prompt "Continue? (Y/N) >." Once you have completed the steps listed above, the DIMM cards are properly loaded. Removing Memory Perform the following steps to remove memory (DIMM cards) from the system unit. 1. Open the side panel of the system unit as explained in the section "Opening the Left Side Panel of the System Unit" in this chapter. 2. Lay the system on its side as shown in Figure 4-58. Chapter 4 143

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239

Chapter 4
143
Field Replaceable Units
FRU Removal and Replacement
Figure 4-57. Installing Memory Cards
7. Place the DIMM card in the connector, lining it up with the guides. Make sure to put
the notched end toward the white ejector tab (to the left). See Figure 4-57.
8.
Close the ejector tab.
9.
Press firmly and evenly on the DIMM card to ensure that it seats properly. The ejector
tabs engage when the DIMM is properly seated.
10.Replace the power supply and workstation left side panel. You may now plug the power
cord back in to the electrical outlet.
11.Verify that this installation was successful by following the steps in Chapter 6, “The
Boot Console Handler.” If you have only replaced a faulty DIMM, you must execute the
pdt clear
command in the service menu of the Boot Console Handler. Answer yes (
Y
)
to the prompt “
Continue? (Y/N) >
.”
Once you have completed the steps listed above, the DIMM cards are properly loaded.
Removing Memory
Perform the following steps to remove memory (DIMM cards) from the system unit.
1. Open the side panel of the system unit as explained in the section “Opening the Left
Side Panel of the System Unit” in this chapter.
2.
Lay the system on its side as shown in Figure 4-58.
Press down on ejector tabs to open
them and place the DIMM card in
the connector so that your fingers
are on the edge of the DIMM card.
Push the DIMM card down firmly
and evenly into the connector to
be sure it is properly seated.
White Ejector Tab
Black
Ejector Tab
Notches
Step 1
Step 2