HP Workstation x2000 hp workstation x2000 - Windows and Linux - Getting Starte - Page 18

Setting Up Your x2000 Workstation

Get HP Workstation x2000 PDF manuals and user guides View all HP Workstation x2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Setting Up and Using Your Workstation Setting Up Your x2000 Workstation WARNING Setting Up Your x2000 Workstation If you have any doubt that you can lift the Workstation or monitor safely, do not try to move them without help. 1. When you receive your Workstation, verify that you have all of the components as shipped. 2. Place the Workstation in an area with easily accessible power outlets and enough space for the keyboard, mouse, and any other accessories. 3. Position the Workstation so that its rear connectors are easily accessible. Installation Tools No tools are required to set up your Workstation. However, if you plan to install or replace an accessory inside your Workstation, you will need a T-15 Torx screwdriver and a flat-blade screwdriver. Connecting Devices Before connecting any cords or cables to your Workstation, please read the Warning Notices in the Preface of this manual. If you purchased a graphics card that was not installed in your Workstation at the factory, you must install that card now. To install, refer to the instructions that came with the card or see the x2000 Technical Reference/Troubleshooting Guide available at: www/hp.com/workstations/support. 16 Chapter 1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Setting Up and Using Your Workstation
Setting Up Your x2000 Workstation
Chapter 1
16
Setting Up Your x2000 Workstation
WARNING
If you have any doubt that you can lift the Workstation or
monitor safely, do not try to move them without help.
1.
When you receive your Workstation, verify that you have all of the
components as shipped.
2.
Place the Workstation in an area with easily accessible power outlets
and enough space for the keyboard, mouse, and any other accessories.
3.
Position the Workstation so that its rear connectors are easily
accessible.
Installation Tools
No tools are required to set up your Workstation. However, if you plan to
install or replace an accessory inside your
Workstation, you will need a
T-15 Torx screwdriver and a flat-blade screwdriver.
Connecting Devices
Before connecting any cords or cables to your Workstation, please read
the
Warning Notices
in the Preface of this manual.
If you purchased a graphics card that was not installed in your
Workstation at the factory, you must install that card now. To install,
refer to the instructions that came with the card or see the
x2000
Technical Reference/Troubleshooting Guide
available at:
www/hp.com/workstations/support.