HP st5747 Troubleshooting Guide: HP t5740/t5745 Thin Clients and HP st5742/st5 - Page 35

Setup Utility—Power Management Setup, Setup Utility—Utility Task Actions

Get HP st5747 - Streaming Client PDF manuals and user guides View all HP st5747 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Setup Utility-Power Management Setup Table 4-6 Setup Utility-Power Management Setup Option Description PWRON After PWRFail When power is lost and comes back, the option determines what power state the system should go to. Options are Off, On, and Former-Sts. Default is Former-Sts. Wake on PME Enable/disable system wakeup capability for OnBoard LAN device and PCI card. Default is enabled. EuP LOT6 Associated with "wake on PME". Disabled allows wake on LAN capability. Enabled puts onboard LAN device in a low power state and disables "wake on PME" automatically. BIOS Wake up Enable RTC alarm wakeup. Default is disabled. Day of Week Select the alarm RTC wakeup day of Sunday through Saturday. Time of Day Select the alarm RTC wakeup time of day (hh:mm:ss). Setup Utility-Utility Task Actions Table 4-7 Setup (F10) Utility Task Actions Heading Table Load Factory Defaults Select OK or Cancel. Set Administrator Password Allows you to set, change, and disable the administrator password. Set User Password Allows you to set, change, and disable the user password. NOTE: When the user password is set, it prevents unauthorized access to the user's setup. User password provides read-only access to Setup options. Save & Exit Setup Saves data to CMOS, then exit the Setup Utility. Exit without Saving Exit the Setup Utility without saving any changes. Using the BIOS Settings 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
Setup Utility—Power Management Setup
Table 4-6
Setup Utility—Power Management Setup
Option
Description
PWRON After PWR-
Fail
When power is lost and comes back, the option determines what power state the system should
go to. Options are Off, On, and Former-Sts. Default is Former—Sts.
Wake on PME
Enable/disable system wakeup capability for OnBoard LAN device and PCI card. Default is
enabled.
EuP LOT6
Associated with “wake on PME”. Disabled allows wake on LAN capability. Enabled puts onboard
LAN device in a low power state and disables “wake on PME” automatically.
BIOS Wake up
Enable RTC alarm wakeup. Default is disabled.
Day of Week
Select the alarm RTC wakeup day of Sunday through Saturday.
Time of Day
Select the alarm RTC wakeup time of day (hh:mm:ss).
Setup Utility—Utility Task Actions
Table 4-7
Setup (F10) Utility Task Actions
Heading
Table
Load Factory Defaults
Select OK or Cancel.
Set Administrator Password
Allows you to set, change, and disable the administrator password.
Set User Password
Allows you to set, change, and disable the user password.
NOTE:
When the user password is set, it prevents unauthorized access to the user's
setup. User password provides read-only access to Setup options.
Save & Exit Setup
Saves data to CMOS, then exit the Setup Utility.
Exit without Saving
Exit the Setup Utility without saving any changes.
Using the BIOS Settings
27