HP t628 t628 Thin Client - Page 55

Diagnostic front panel LEDs and audible codes continued, Table B-3

Get HP t628 PDF manuals and user guides View all HP t628 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 55 highlights

Table B-3 Diagnostic front panel LEDs and audible codes (continued) Activity Beeps Possible Cause Recommended Action 3. Replace third-party memory with HP memory. 4. Replace the system board. Red Power LED flashes six times, 6 once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. Pre-video graphics error. For systems with a graphics card: 1. Reseat the graphics card. 2. Replace the graphics card. 3. Replace the system board. For systems with integrated graphics, replace the system board. Red Power LED flashes eight 8 times, once every second, followed by a two second pause. Beeps stop after fifth iteration but LEDs continue until problem is solved. Invalid ROM based on bad checksum. 1. Reflash the system ROM with the latest BIOS image using the BIOS Recovery procedure. 2. Replace the system board. System does not power on and LEDs are not flashing. None System unable to power on. Press and hold the power button for less than four seconds. If the hard drive LED turns white, the power button is working correctly. Try the following: 1. Remove the power cord from the computer. 2. Open the computer and press the yellow CMOS button on the system board for four seconds (located near the front USB ports). 3. Verify that the AC cord is plugged into the power supply. 4. Close the unit and reattach the power cord. 5. Try to power on the computer. 6. Replace the unit. Interpreting POST diagnostic front panel LEDs and audible codes 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
Table B-3
Diagnostic front panel LEDs and audible codes (continued)
Activity
Beeps
Possible Cause
Recommended Action
3.
Replace third-party memory with HP memory.
4.
Replace the system board.
Red Power LED
flashes
six times,
once every second, followed by a
two second pause. Beeps stop
after
fifth
iteration but LEDs
continue until problem is solved.
6
Pre-video graphics error.
For systems with a graphics card:
1.
Reseat the graphics card.
2.
Replace the graphics card.
3.
Replace the system board.
For systems with integrated graphics, replace the
system board.
Red Power LED
flashes
eight
times, once every second,
followed by a two second pause.
Beeps stop after
fifth
iteration
but LEDs continue until problem
is solved.
8
Invalid ROM based on bad
checksum.
1.
Reflash
the system ROM with the latest BIOS
image using the BIOS Recovery procedure.
2.
Replace the system board.
System does not power on and
LEDs are not
flashing.
None
System unable to power on.
Press and hold the power button for less than four
seconds. If the hard drive LED turns white, the power
button is working correctly. Try the following:
1.
Remove the power cord from the computer.
2.
Open the computer and press the yellow CMOS
button on the system board for four seconds
(located near the front USB ports).
3.
Verify that the AC cord is plugged into the
power supply.
4.
Close the unit and reattach the power cord.
5.
Try to power on the computer.
6.
Replace the unit.
Interpreting POST diagnostic front panel LEDs and audible codes
49