Home » Honeywell Manuals » Barcode Scanners » Honeywell MS9535-5 » Manual Viewer

Honeywell MS9535-5 Configuration Guide - Page 65

Keyboard, Enable Keyboard Emulation, Country/Scan Code Table Selects

Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

11 Keyboard Enable Keyboard Emulation ³ 999994 Load Keyboard Wedge Defaults - Loads the default settings for keyboard wedge mode. ³ 5155153 Enable Stand-Alone Keyboard Emulation - Use this with special stand-alone models that are not cabled for an external keyboard. Scan this bar code to enable the Stand-Alone Mode. The scanner will send keyboard "power on" information and configure hardware to simulate a constant keyboard connection. * Enable Keyboard Wedge Emulation - Use this ³ 5 1 5 5 1 4 3 with an external keyboard. Transmit in wedge made to allow standard PC keyboards to communicate when no bar code data is available. Country/Scan Code Table Selects ³ 416260 * USA Keyboard ³ 416280 Switzerland Keyboard ³ 416250 Spain Keyboard ³ 416240 Italy Keyboard ³ 416230 Germany Keyboard ³ 416220 France Keyboard ³ 416210 UK Keyboard 11-1

Section	Page
MetroSelect Configuration Guide	1
Disclaimer / Trademarks	2
Table of Contents	3
Introduction	7
Bar Code Configuration Methods	7
Single-Code Method	7
Multi-Code Method	7
Need To Start Over?	8
Code Types and Decode Rules	9
UPC/EAN	9
Code 128	10
Code 39	10
2 of 5 Codes	12
Codabar	14
Code 93	14
Code 11	14
Telepen	15
Plessey Codes	15
Additional Decode Features	16
Configurable Code Lengths	17
Supplements	19
GS1 DataBar	25
GS1 DataBar Limited	26
GS1 DataBar Expanded	26
ISBT Code 128 Implementation	27
Configuration Mode	27
Concatenation Configuration Mode	28
Pre-Defined Concatenation Configuration Mode	28
User-Defined Concatenation Configuration Mode	29
Communications	31
Scanner Operation	33
Configuration Mode Options	33
Scan Buffers	33
Redundant Scans	34
Miscellaneous Decode Features	34
Same Symbol Time Outs	35
LED Options	35
Beeper Options	36
Data Transmission Delays	38
Communication Time Out Options	39
Host Scanner Commands	40
Test Modes	42
Prefixes/Suffixes	43
User Configurable Prefixes, All Data	43
User Configurable ID Characters, Code Specific	44
Standard Prefix Characters	46
Standard Suffix Characters	48
Longitudinal Redundancy Check	49
Block Check Character	49
Character Replacements	50
User Configurable Suffixes, All Data	51
Special Formats	52
Code Formatting	53
UPC/EAN Formatting	53
Codabar Formatting	55
Code 39 Formatting	56
Code 11 Formatting	56
Telepen	56
Plessey	57
2 of 5 Code Formatting	57
RS232	59
Parity Features	59
Baud Rate	59
Data/Stop Bits	60
Hardware Handshaking	60
Software Handshaking	62
Miscellaneous	63
Keyboard	65
Enable Keyboard Emulation	65
Country/Scan Code Table Selects	65
Keyboard/System Type	66
‘Dumb’ Terminal Selections	67
Special Keyboard Features	68
InterScan Code Delays	70
Control Sets	71
OCIA	73
Light Pen Parameters	75
Set Narrow Element Width	76
RS485 Configuration	77
IBM Port	77
IBM Reserved Codes	77
USB	79
Code Bytes Usage	81
Code Bytes 0–9	81
Reserved Codes	82
Code Type Table	82
ASCII Reference Table	83
Extended Key Code Reference Table	87
MS9520 Voyager® and MS9540 VoyagerCG® Series	89
Activation Range	89
Stand Scan Modes	89
CodeGate Status	89
Laser/Scan Modes	90
Same Symbol Time Outs	91
MS9520-00 and MS9540-00 Laser Emulation Mode	92
MS9524 and MS9544 VoyagerPDF® Series	93
PDF CodeGate Status	93
MicroPDF and Composite Code Handling	93
MS9535 VoyagerBT®	95
MS9535-5M VoyagerBT	97
Inventory Quantity Bar Codes	99
IS4125 and IS4225 Scan Engines	101
IS4823 and IS4825 Scan Engines	103
Operating Modes	103
Miscellaneous Features	107
Custom Defaults	107
Serial Program Mode	108
Customer Support	109
Technical Assistance	109