Honeywell MS9535-5 Configuration Guide - Page 7

Introduction, Bar Code Configuration Methods, Single-Code Method, Multi-Code Method - enable scanning in base

Get Honeywell MS9535-5 PDF manuals and user guides View all Honeywell MS9535-5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

1 Introduction Your new scanner has been factory configured with a set of default parameters. Since many host systems have unique formats and protocol requirements, Honeywell provides a wide range of configurable features that may be selected using this bar code based configuration tool. Once the configuration is completed, the scanner stores the settings in nonvolatile memory (NOVRAM). NOVRAM saves the settings when the power is off. Note: Bar code descriptions marked with an asterisk ( * ) define a feature that is a factory default. Bar codes marked with a tilde ( ~ ) require the Multi-Code configuration method. Bar Code Configuration Methods The MetroSelect class of scanners can be bar code configured in two ways: the Single-Code Method and the Multi-Code Method. Note: To properly configure an MS9540 scanner, all configuration codes must be scanned using the CodeGate® option. Single-Code Method Most features can be enabled or disabled using the Single-Code Method. 1. Power-up the scanner. 2. Scan the bar code for the desired feature. 3. The scanner will emit a multi-toned beep to indicate the configuration has been saved to NOVRAM. Multi-Code Method All features can be enabled or disabled using the Multi-Code Method. A feature marked with a tilde ( ~ ) requires the Multi-Code Method. 1. Power-up the scanner. 2. Scan the enter/exit configuration mode bar code (3 beeps). 3. Scan the bar code for the desired feature (1 beep). Multiple features can be enabled/disabled before scanning the enter/exit configuration mode bar code. 4. Scan the enter/exit configuration mode bar code (3 beeps) and save the new configuration. To abort a configuration change, power off the scanner before scanning the enter/exit code. Enter/Exit Configuration Mode ³ 999999 1-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
1–1
Introduction
Your new scanner has been factory configured with a set of default
parameters. Since many host systems have unique formats and protocol
requirements, Honeywell provides a wide range of configurable features
that may be selected using this bar code based configuration tool. Once the
configuration is completed, the scanner stores the settings in nonvolatile
memory (NOVRAM). NOVRAM saves the settings when the power is off.
Note:
Bar code descriptions marked with an asterisk ( * ) define a feature that
is a factory default. Bar codes marked with a tilde ( ~ ) require the
Multi-Code configuration method.
Bar Code Configuration Methods
The MetroSelect class of scanners can be bar code configured in two ways:
the
Single-Code Method
and the
Multi-Code Method
.
Note:
To properly configure an MS9540 scanner, all configuration
codes must be scanned using the CodeGate
®
option.
Single-Code Method
Most features can be enabled or disabled using the Single-Code Method.
1.
Power-up the scanner.
2.
Scan the bar code for the desired feature.
3.
The scanner will emit a multi-toned beep to indicate the configuration
has been saved to NOVRAM.
Multi-Code Method
All features can be enabled or disabled using the Multi-Code Method.
A feature marked with a tilde ( ~ ) requires the Multi-Code Method.
1.
Power-up the scanner.
2.
Scan the
enter/exit configuration mode
bar code (3 beeps).
3.
Scan the bar code for the desired feature (1 beep). Multiple features
can be enabled/disabled before scanning the enter/exit configuration
mode bar code.
4.
Scan the
enter/exit configuration mode
bar code (3 beeps) and save
the new configuration. To abort a configuration change, power off the
scanner before scanning the
enter/exit
code.
Enter/Exit Configuration Mode
³
9
9
9
9
9
9
1