Hoover U6485100 Manual - Page 14

V-belt, Brushroll - replace agitator belt

Get Hoover U6485100 PDF manuals and user guides View all Hoover U6485100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

V-belt ! WARNING ! Agitator brushroll can start suddenly. Unplug cleaner before turning it over. How to Inspect The V-belt is designed to last for a long time and is not normally replaced. However, if V-belt is cracked, gouged or broken, now is a good time to replace it as follows. Slide flat belt off large pulley as shown in Fig. 3.10. How to Remove 3.14 To remove V-belt, slide back of belt over pulley (C). Then firmly pull on belt and "snap" it out. Discard used belt and replace. To install new belt (with lettering on outside of belt), slide back of belt over pulley and pull front of belt toward groove (E) next to pulley. Belt will "pop" into place. Positioning Belt on Brushroll Before positioning belt onto brushroll, check for debris accumulation as described in Fig. 3.23. 3.15 Insert brushroll through belt and position belt in groove (F) on brushroll. 3.14 E C 3.15 F What to Buy: V-Belt When purchasing a new V-Belt, ask for HOOVER® part No. 38528034. If desired, additional belts can be purchased at Hoover.com or 1-800-944-9200. Brushroll ! WARNING ! Agitator brushroll can start suddenly. Unplug cleaner before turning it over. 3.16 3.17 When to Replace Unplug cleaner when it is turned over. When brushroll brushes are worn, it should be replaced. 3.16 To check condition of brushes, move the edge of a card across bottom plate while turning brushroll. To maintain cleaning effectiveness, replace brushroll if brushes do not touch card. How to Remove 3.17 Slide Brushroll Control (Fig. 2.9) to "Hard" (OFF) position. Turn cleaner over and remove bottom plate (Fig. 3.9). Lift up brushroll and slide V-belt (D) off brushroll. How to Install 3.18 Grasp brushroll and fit it into position by first sliding end, opposite the belt, into the rectangular slot (G) on side of cleaner. Push other side of brushroll (H) into place. Belt may fit loosely when properly installed. Reposition flat belt and bottom plate (Fig. 3.13) D 3.18 G H What to Buy: Brushroll When purchasing a new brushroll, ask for HOOVER® part No. 48414144. If desired, additional brushroll can be purchased at Hoover.com or 1-800-944-9200. Actual model may vary from images shown. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
D
3.17
H
G
3.18
What to Buy: V-Belt
When purchasing a new V-Belt, ask for
HOOVER
®
part
No. 38528034.
If desired, additional belts can be purchased
at Hoover.com or 1-800-944-9200.
When to Replace
Unplug cleaner when it is turned over. When
brushroll brushes are worn, it should be replaced.
3.16 To check condition of brushes, move
the edge
of a card across bottom plate while turning brushroll.
To maintain cleaning effectiveness, replace brushroll
if brushes do not touch card.
How to Remove
3.17 Slide Brushroll Control (Fig. 2.9) to “Hard” (OFF)
position. Turn cleaner over and remove bottom plate
(Fig. 3.9). Lift up brushroll and slide V-belt (D) off
brushroll.
How to Install
3.18 Grasp brushroll and fit it into position by first
sliding end, opposite the belt, into the rectangular
slot (G) on side of cleaner.
3.16
How to Inspect
The V-belt is designed to last for a long time and is
not normally replaced.
However, if V-belt is cracked,
gouged or broken, now is a good time to replace it
as follows.
Slide flat belt off large pulley as shown in Fig. 3.10.
How to Remove
3.14 To remove V-belt, slide back of belt over pulley
(C). Then firmly pull on belt and “snap” it out.
Discard used belt and replace.
To install new belt (with lettering on outside of belt),
slide back of belt over pulley and pull front of belt
toward groove (E) next to pulley.
Belt will “pop” into place.
C
E
F
3.14
3.15
V-BELT
WARNING
!
!
Agitator brushroll can start suddenly. Unplug
cleaner before turning it over.
WARNING
!
!
Agitator brushroll can start suddenly. Unplug
cleaner before turning it over.
BRUSHROLL
14
Actual model may vary from images shown.
What to Buy: Brushroll
When purchasing a new brushroll, ask for
HOOVER
®
part No.
48414144
.
If desired, additional brushroll can be purchased
at Hoover.com or 1-800-944-9200.
Positioning Belt on Brushroll
Before positioning belt onto brushroll, check for
debris accumulation as described in Fig. 3.23.
3.15 Insert brushroll through belt and position belt in
groove (F) on brushroll.
Push other side of brushroll (H) into place.
Belt may
fit loosely when properly installed. Reposition flat
belt and bottom plate (Fig. 3.13)