Husqvarna 520iHD60 Owner Manual - Page 12

Maintenance

Get Husqvarna 520iHD60 PDF manuals and user guides View all Husqvarna 520iHD60 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

3. Make sure that the motor does not touch the hedge. 4. Hold the product near your body for a stable work position. 5. Make sure that the tip of the cutting equipment does not touch the ground. 6. Be careful and work slowly until all the branches are correctly cut. To start the SavE function The product has a battery saving function, SavE. 1. Push the SavE button to start the function. A green LED comes on to show that the function is on. WARNING: Do not operate the cutting attachment when you adjust the handle. To stop the product 1. Release the power trigger or the power trigger lockout. 2. Push the start/stop button until the green LED goes out. 3. Push the release buttons on the battery and pull the battery out. Automatic shutdown function The product has an automatic shutdown function that stops the product if it is not used. The green LED for start/stop indication goes off and the product stops after 45 seconds. To adjust the angle of the product To get the best operation position, this product can be adjusted in 5 different positions. If the angle is adjusted, make sure that the bottom of the rear handle points down when you operate the product. 1. Release the handle lock and turn the handle. Maintenance Introduction WARNING: Read and understand the safety chapter before you do maintenance work on the product. WARNING: Remove the battery before you do maintenance on the product. 12 773 - 004 - 19.08.2020

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
3.
Make sure that the motor does not touch the hedge.
4.
Hold the product near your body for a stable work
position.
5.
Make sure that the tip of the cutting equipment does
not touch the ground.
6.
Be careful and work slowly until all the branches are
correctly cut.
To start the SavE function
The product has a battery saving function, SavE.
1.
Push the SavE button to start the function. A green
LED comes on to show that the function is on.
Automatic shutdown function
The product has an automatic shutdown function that
stops the product if it is not used. The green LED for
start/stop indication goes off and the product stops after
45 seconds.
To adjust the angle of the product
To get the best operation position, this product can be
adjusted in 5 different positions. If the angle is adjusted,
make sure that the bottom of the rear handle points
down when you operate the product.
1.
Release the handle lock and turn the handle.
WARNING:
Do not operate the cutting
attachment when you adjust the handle.
To stop the product
1.
Release the power trigger or the power trigger
lockout.
2.
Push the start/stop button until the green LED goes
out.
3.
Push the release buttons on the battery and pull the
battery out.
Maintenance
Introduction
WARNING:
Read and understand the safety
chapter before you do maintenance work on
the product.
WARNING:
Remove the battery before you
do maintenance on the product.
12
773 - 004 - 19.08.2020