Husqvarna 525iLK Owner Manual - Page 12

To disassemble the two-piece shaft, To install the harness support hook, To adjust the harness

Get Husqvarna 525iLK PDF manuals and user guides View all Husqvarna 525iLK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

3. Push the shaft into the coupling until it clicks into position. 4. Pull the attachment out of the coupling. 4. Tighten the knob fully. C To install the harness support hook 1. Install the harness support hook between the loop handle and the throttle handle. To disassemble the two-piece shaft 1. Turn the knob 3 turns or more to loosen the coupling. 2. Push and hold the button (C). 3. Hold tight in the end of the shaft that the motor is attached to. Note: Do not put the support hook on the decal. 2. Adjust the ring to make the product balanced, and easy to use. To adjust the harness 1. Put on the harness. 2. Attach the harness to the harness support hook. 3. Adjust the length of the harness until the harness support hook is in level with your right hip. To assemble the cutting equipment The cutting equipment includes a cutting attachment and a cutting attachment guard. WARNING: Use protective gloves. WARNING: Always use the cutting attachment guard that is recommended for the cutting attachment. See Technical data on page 19. 12 1938 - 003 - 24.02.2023

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
3.
Push the shaft into the coupling until it clicks into
position.
4.
Tighten the knob fully.
To disassemble the two-piece shaft
1.
Turn the knob 3 turns or more to loosen the
coupling.
2.
Push and hold the button (C).
3.
Hold tight in the end of the shaft that the motor is
attached to.
4.
Pull the attachment out of the coupling.
C
To install the harness support hook
1.
Install the harness support hook between the loop
handle and the throttle handle.
Note:
Do not put the support hook on the decal.
2.
Adjust the ring to make the product balanced, and
easy to use.
To adjust the harness
1.
Put on the harness.
2.
Attach the harness to the harness support hook.
3.
Adjust the length of the harness until the harness
support hook is in level with your right hip.
To assemble the cutting equipment
The cutting equipment includes a cutting attachment and
a cutting attachment guard.
WARNING:
Use protective gloves.
WARNING:
Always use the cutting
attachment guard that is recommended for
the cutting attachment. See
Technical data
on page 19
.
12
1938 - 003 - 24.02.2023