Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 315X with installation service » Manual Viewer

Husqvarna AUTOMOWER 315X with installation service Owner Manual - Page 40

Maintenance, Introduction - maintenance, Clean the product, Chassis and blade disc, Wheels

View all Husqvarna AUTOMOWER 315X with installation service manuals

Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

5 Maintenance 5.1 Introduction - maintenance WARNING: The product must be switched off before any maintenance is done. WARNING: Wear protective gloves. For better operation and longer service life, make sure to clean the product regularly and replace worn parts. All maintenance and servicing must be done according to Husqvarna's instructions. Refer to Warranty on page 58. When the product is first used, the blade disc and blades should be inspected once a week. If the amount of wear during this period has been low, the inspection interval can be increased. It is important that the blade disc rotates easily. The edges of the blades should not be damaged. The lifetime of the blades varies immensely and depends for instance on: • Operating time and size of the work area. • Type of grass and seasonal growth. • Soil, sand and use of fertilizers. • The presence of objects such as cones, windfalls, toys, tools, stones, roots and the like. The normal life is 3 to 6 weeks when used under favorable conditions. Refer to Replace the blades on page 41 on how to replace the blades. Note: Working with blunt blades gives a poorer mowing result. The grass is not cut cleanly and more energy is needed resulting in the product not mowing such a large area. 5.2 Clean the product CAUTION: Never use a high-pressure washer to clean the product. Never use solvents for cleaning. Husqvarna recommends to use a special cleaning and maintenance kit, available as accessory. Speak to your Husqvarna representative for more information. 5.2.1 Chassis and blade disc Inspect the blade disc and blades once a week. 1. Push the STOP button. 2. Set the Main switch to position 0. 3. Lift the product onto its side. 4. Clean the blade disc and chassis using for example a dish brush. At the same time, check that the blade disc rotates freely in relation to the foot guard. Also, check that the blades are intact and can pivot freely. 5.2.2 Wheels Clean around the wheels. Grass on the wheels can impact on how the product performs in slopes. 5.2.3 The body of the product Use a moist, soft sponge or cloth to clean the body of the product. If the body of the product is dirty, use a mild soap solution to clean it. 5.2.4 Charging station WARNING: Use the plug to disconnect the charging station before any maintenance, or cleaning of charging station or power supply. Clean the charging station regularly from grass, leaves, twigs and other objects that may impede docking. The product does not operate satisfactorily in slopes if the wheels are blocked with grass. Use a soft brush to clean the product. 40 - Maintenance 1440 - 002 - 19.02.2020

Section	Page
Contents	2
Introduction	3
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Product overview Automower® 310/315/315X	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview - 1	7
Menu structure overview - 2	8
Display	9
Keypad	9
Safety	10
Safety information	10
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	10
Safety definitions	11
Safety instructions for operation	11
Use	11
Battery safety	12
How to lift and move the product	12
Maintenance	13
In the event of a thunderstorm	13
Installation	15
Introduction - Installation	15
Main components for installation	15
General preparations	15
Before the installation of the wires	15
To examine where to put the charging station	15
To examine where to put the power supply	16
To examine where to put the boundary wire	16
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To examine where to put the guide wire	19
Work area examples	20
Installation of the product	20
Installation tools	20
To install the charging station	20
To install the boundary wire	21
To install the guide wire	22
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	23
To extend the boundary wire or the guide wire	23
After the installation of the product	23
To do a visual check of the charging station	23
To do the basic settings	23
Calibration	24
To do the product settings	24
Menu structure	24
To get access to the menu	24
Schedule	24
To set the schedule	24
To calculate the suitable operating hours	24
To copy the schedule setting	25
To reset the schedule setting	25
Security level	25
To set the security level	25
To create a New loop signal	25
To change the PIN-code	26
To change the length of the alarm	26
To change the length of the time lock	26
Messages	26
To read the messages	26
Weather timer	26
To set the Weather timer	26
To set the Weather timer frequency	27
Lawn Coverage	27
GPS Assisted Navigation	27
To set the GPS Assisted Navigation	27
To set the Lawn Coverage function	27
To do a test of the Lawn Coverage function	28
To measure the distance from the charging station	28
To disable or enable the Lawn Coverage function	28
To reset the Lawn Coverage settings	28
Methods for the product to find the charging station	28
To set how the product finds the charging station	29
To do a test of the guide wire	29
To do a test of the boundary wire	29
To change the signal range of the charging station	29
Corridor width	29
To set the corridor width	30
Exit angle	30
To set the exit angle	30
Reversing distance	30
To set the reversing distance	30
Drive Past Wire function	30
To set the Drive Past Wire function	30
Settings	30
Profiles	31
To save settings to a profile	31
To change the name of a profile	31
To use a profile	31
To connect a new charging station to a profile	31
ECO mode	31
To set the ECO mode	31
Spiral Cutting	31
To set the Spiral Cutting	31
To set the level of Spiral Cutting	32
Slope control	32
To set the Slope control	32
General	32
To set the time & date	32
To set the language	32
To set the Country & Timezone	32
To set the unit format	32
To reset all user settings	32
The About menu	32
Accessories	33
Information	33
Automower® Connect app	33
To install the Automower® Connect app	33
Automower® Connect@Home	33
To pair Connect@Home and the product	33
To remove paired accounts	33
Automower® Connect	33
To pair Automower® Connect and the product	33
To enable the GeoFence function	34
To set a new center point for the Geofence function	34
To set the GeoFence level of sensitivity	34
To use the SMS function	34
Network	34
APN settings	34
Headlights Automower® 315X	34
To set the schedule for the headlights	34
To set the Flashes when fault function	34
To avoid collisions with the mower house	35
Operation	36
Main switch	36
To start the product	36
Operating mode Start	36
Main area	36
Secondary area	36
Override schedule	37
Spot cutting	37
Operating mode Park	37
Park until further notice	37
Start again with next schedule	37
To stop the product	37
To switch off the product	37
Schedule and Standby	37
Example 1	38
Example 2	38
To charge the battery	38
Adjust the cutting height	39
To adjust the cutting height	39
Maintenance	40
Introduction - maintenance	40
Clean the product	40
Chassis and blade disc	40
Wheels	40
The body of the product	40
Charging station	40
Replace the blades	41
To replace the blades	41
Battery	41
Winter service	42
Troubleshooting	43
Introduction - troubleshooting	43
Fault messages	43
Information messages	48
Indicator lamp in the charging station	49
Symptoms	50
Find breaks in the loop wire	51
Transportation, storage and disposal	54
Transportation	54
Storage	54
Disposal	54
To remove the battery	54
Technical data	55
Technical data	55
Registered trademarks	57
Warranty	58
Warranty terms	58
EC Declaration of Conformity	59

Match case Limit results 1 per page

5 Maintenance

5.1 Introduction - maintenance

WARNING:

The product must be

switched off before any maintenance is

done.

WARNING:

Wear protective gloves.

For better operation and longer service life, make

sure to clean the product regularly and replace

worn parts. All maintenance and servicing must

be done according to Husqvarna's instructions.

Refer to

Warranty on page 58

When the product is first used, the blade disc and

blades should be inspected once a week. If the

amount of wear during this period has been low,

the inspection interval can be increased.

It is important that the blade disc rotates easily.

The edges of the blades should not be damaged.

The lifetime of the blades varies immensely and

depends for instance on:

•

Operating time and size of the work area.

•

Type of grass and seasonal growth.

•

Soil, sand and use of fertilizers.

•

The presence of objects such as cones,

windfalls, toys, tools, stones, roots and the

like.

The normal life is 3 to 6 weeks when used under

favorable conditions. Refer to

Replace the blades

on page 41

on how to replace the blades.

Note:

Working with blunt blades gives a poorer

mowing result. The grass is not cut cleanly and

more energy is needed resulting in the product

not mowing such a large area.

5.2 Clean the product

CAUTION:

Never use a high-pressure

washer to clean the product. Never

use solvents for cleaning.

The product does not operate satisfactorily in

slopes if the wheels are blocked with grass. Use

a soft brush to clean the product.

Husqvarna recommends to use a special

cleaning and maintenance kit, available as

accessory. Speak to your Husqvarna

representative for more information.

5.2.1 Chassis and blade disc

Inspect the blade disc and blades once a week.

Push the

STOP

button.

Set the

Main switch

to position

Lift the product onto its side.

Clean the blade disc and chassis using for

example a dish brush. At the same time,

check that the blade disc rotates freely in

relation to the foot guard. Also, check that

the blades are intact and can pivot freely.

5.2.2 Wheels

Clean around the wheels. Grass on the wheels

can impact on how the product performs in

slopes.

5.2.3 The body of the product

Use a moist, soft sponge or cloth to clean the

body of the product. If the body of the product is

dirty, use a mild soap solution to clean it.

5.2.4 Charging station

WARNING:

Use the plug to disconnect

the charging station before any

maintenance, or cleaning of charging

station or power supply.

Clean the charging station regularly from grass,

leaves, twigs and other objects that may impede

docking.

- Maintenance

1440 - 002 - 19.02.2020