Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 315X with installation service » Manual Viewer

Husqvarna AUTOMOWER 315X with installation service Owner Manual - Page 48

Information messages, Indicator lamp in the charging station

View all Husqvarna AUTOMOWER 315X with installation service manuals

Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

6.3 Information messages The information messages in the table below are shown in the display of the product. Speak to your Husqvarna representative if the same message shows frequently. Message Low battery Cause The product cannot find the charging station. Action Change the position of the guide wire. Refer to To install the guide wire on page 22. Check the settings. Refer to To set how the product finds the charging station on page 29. The battery is spent. Replace the battery. Refer to Battery on page 41. The charging station's antenna is defective. Check if the indicator lamp in the charging station flashes red. Refer to Indicator lamp in the charging station on page 49. The charging plates on the product or contact plates on the charging station are corroded. Clean the charging and contact plates using a fine grade emery cloth. If the problem stays speak to your approved servicing dealer. Settings restored Confirmation that Reset all user settings has been carried out. No action. Guide not found The guide wire is not connected to the charging station. Check that the guide wire connector is tightly connected to the charging station. Refer to To install the guide wire on page 22. Break in the guide wire. Find out where the break is and rectify it. The guide wire is not connected to the boundary loop. Check that the guide wire is connected correctly to the boundary loop. Refer to To install the boundary wire on page 21. Guide calibration failed The product has failed to calibrate the guide wire. Check that the guide wire is installed according to the instructions. Refer to To install the guide wire on page 22. Guide calibration The product has succeeded to calibrate No action. done the guide wire. Connection changed New loop signal successfully changed. No action. 48 - Troubleshooting 1440 - 002 - 19.02.2020

Section	Page
Contents	2
Introduction	3
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Product overview Automower® 310/315/315X	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview - 1	7
Menu structure overview - 2	8
Display	9
Keypad	9
Safety	10
Safety information	10
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	10
Safety definitions	11
Safety instructions for operation	11
Use	11
Battery safety	12
How to lift and move the product	12
Maintenance	13
In the event of a thunderstorm	13
Installation	15
Introduction - Installation	15
Main components for installation	15
General preparations	15
Before the installation of the wires	15
To examine where to put the charging station	15
To examine where to put the power supply	16
To examine where to put the boundary wire	16
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To examine where to put the guide wire	19
Work area examples	20
Installation of the product	20
Installation tools	20
To install the charging station	20
To install the boundary wire	21
To install the guide wire	22
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	23
To extend the boundary wire or the guide wire	23
After the installation of the product	23
To do a visual check of the charging station	23
To do the basic settings	23
Calibration	24
To do the product settings	24
Menu structure	24
To get access to the menu	24
Schedule	24
To set the schedule	24
To calculate the suitable operating hours	24
To copy the schedule setting	25
To reset the schedule setting	25
Security level	25
To set the security level	25
To create a New loop signal	25
To change the PIN-code	26
To change the length of the alarm	26
To change the length of the time lock	26
Messages	26
To read the messages	26
Weather timer	26
To set the Weather timer	26
To set the Weather timer frequency	27
Lawn Coverage	27
GPS Assisted Navigation	27
To set the GPS Assisted Navigation	27
To set the Lawn Coverage function	27
To do a test of the Lawn Coverage function	28
To measure the distance from the charging station	28
To disable or enable the Lawn Coverage function	28
To reset the Lawn Coverage settings	28
Methods for the product to find the charging station	28
To set how the product finds the charging station	29
To do a test of the guide wire	29
To do a test of the boundary wire	29
To change the signal range of the charging station	29
Corridor width	29
To set the corridor width	30
Exit angle	30
To set the exit angle	30
Reversing distance	30
To set the reversing distance	30
Drive Past Wire function	30
To set the Drive Past Wire function	30
Settings	30
Profiles	31
To save settings to a profile	31
To change the name of a profile	31
To use a profile	31
To connect a new charging station to a profile	31
ECO mode	31
To set the ECO mode	31
Spiral Cutting	31
To set the Spiral Cutting	31
To set the level of Spiral Cutting	32
Slope control	32
To set the Slope control	32
General	32
To set the time & date	32
To set the language	32
To set the Country & Timezone	32
To set the unit format	32
To reset all user settings	32
The About menu	32
Accessories	33
Information	33
Automower® Connect app	33
To install the Automower® Connect app	33
Automower® Connect@Home	33
To pair Connect@Home and the product	33
To remove paired accounts	33
Automower® Connect	33
To pair Automower® Connect and the product	33
To enable the GeoFence function	34
To set a new center point for the Geofence function	34
To set the GeoFence level of sensitivity	34
To use the SMS function	34
Network	34
APN settings	34
Headlights Automower® 315X	34
To set the schedule for the headlights	34
To set the Flashes when fault function	34
To avoid collisions with the mower house	35
Operation	36
Main switch	36
To start the product	36
Operating mode Start	36
Main area	36
Secondary area	36
Override schedule	37
Spot cutting	37
Operating mode Park	37
Park until further notice	37
Start again with next schedule	37
To stop the product	37
To switch off the product	37
Schedule and Standby	37
Example 1	38
Example 2	38
To charge the battery	38
Adjust the cutting height	39
To adjust the cutting height	39
Maintenance	40
Introduction - maintenance	40
Clean the product	40
Chassis and blade disc	40
Wheels	40
The body of the product	40
Charging station	40
Replace the blades	41
To replace the blades	41
Battery	41
Winter service	42
Troubleshooting	43
Introduction - troubleshooting	43
Fault messages	43
Information messages	48
Indicator lamp in the charging station	49
Symptoms	50
Find breaks in the loop wire	51
Transportation, storage and disposal	54
Transportation	54
Storage	54
Disposal	54
To remove the battery	54
Technical data	55
Technical data	55
Registered trademarks	57
Warranty	58
Warranty terms	58
EC Declaration of Conformity	59