Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 315X with installation service » Manual Viewer

Husqvarna AUTOMOWER 315X with installation service Owner Manual - Page 44

Alarm! Mower lif, Wrong PIN code

View all Husqvarna AUTOMOWER 315X with installation service manuals

Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Message Empty battery Cause The product cannot find the charging station. The battery is spent. The charging station's antenna is defective. The charging plates on the product or contact plates on the charging station are corroded. Wrong PIN code No drive Wrong PIN code has been entered. Five attempts are permitted, and the keypad is then blocked for a period of time. The product has got caught in something and has been slipping. The work area includes a steep slope. The guide wire is not laid diagonally in the slope. Wheel motor over- Grass or other object is wrapped loaded, left/right around the drive wheel. Collision sensor The product body can not move freely problem, front/rear around its chassis. Alarm! Mower switched off Alarm! Mower stopped Alarm! Mower lifted Alarm! Mower tilted The alarm is activated because the product had been switched off. The alarm is activated because the product has been stopped. The alarm is activated because the product has been lifted. The alarm is activated because the product has been tilted. Action Change the position of the guide wire. Refer to To install the guide wire on page 22. Replace the battery. Refer to Battery on page 41. Check if the indicator lamp in the charging station flashes red. Refer to Indicator lamp in the charging station on page 49. Clean the charging and contact plates using a fine grade emery cloth. If the problem stays speak to your authorized service technician. Enter the correct PIN code. Contact Husqvarna customer service if you forget the PIN code. Free the product and rectify the reason for the lack of drive. If it is due to wet grass, wait until the lawn has dried before using the product. Steep slopes should be isolated. Refer to To put the boundary wire in a slope on page 18. Make sure that the guide wire is installed diagonally across the slope. Refer to To make a secondary area on page 19. Check the drive wheel and remove grass or object. Check that the product body can move freely around its chassis. If the problem stays speak to your authorized service technician. Adjust the security level in the Security menu. Refer to To set the security level on page 25. 44 - Troubleshooting 1440 - 002 - 19.02.2020

Section	Page
Contents	2
Introduction	3
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Product overview Automower® 310/315/315X	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview - 1	7
Menu structure overview - 2	8
Display	9
Keypad	9
Safety	10
Safety information	10
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	10
Safety definitions	11
Safety instructions for operation	11
Use	11
Battery safety	12
How to lift and move the product	12
Maintenance	13
In the event of a thunderstorm	13
Installation	15
Introduction - Installation	15
Main components for installation	15
General preparations	15
Before the installation of the wires	15
To examine where to put the charging station	15
To examine where to put the power supply	16
To examine where to put the boundary wire	16
To put the boundary wire in a slope	18
Passages	18
To make an island	18
To make a secondary area	19
To examine where to put the guide wire	19
Work area examples	20
Installation of the product	20
Installation tools	20
To install the charging station	20
To install the boundary wire	21
To install the guide wire	22
To put the wire into position with stakes	22
To bury the boundary wire or the guide wire	23
To extend the boundary wire or the guide wire	23
After the installation of the product	23
To do a visual check of the charging station	23
To do the basic settings	23
Calibration	24
To do the product settings	24
Menu structure	24
To get access to the menu	24
Schedule	24
To set the schedule	24
To calculate the suitable operating hours	24
To copy the schedule setting	25
To reset the schedule setting	25
Security level	25
To set the security level	25
To create a New loop signal	25
To change the PIN-code	26
To change the length of the alarm	26
To change the length of the time lock	26
Messages	26
To read the messages	26
Weather timer	26
To set the Weather timer	26
To set the Weather timer frequency	27
Lawn Coverage	27
GPS Assisted Navigation	27
To set the GPS Assisted Navigation	27
To set the Lawn Coverage function	27
To do a test of the Lawn Coverage function	28
To measure the distance from the charging station	28
To disable or enable the Lawn Coverage function	28
To reset the Lawn Coverage settings	28
Methods for the product to find the charging station	28
To set how the product finds the charging station	29
To do a test of the guide wire	29
To do a test of the boundary wire	29
To change the signal range of the charging station	29
Corridor width	29
To set the corridor width	30
Exit angle	30
To set the exit angle	30
Reversing distance	30
To set the reversing distance	30
Drive Past Wire function	30
To set the Drive Past Wire function	30
Settings	30
Profiles	31
To save settings to a profile	31
To change the name of a profile	31
To use a profile	31
To connect a new charging station to a profile	31
ECO mode	31
To set the ECO mode	31
Spiral Cutting	31
To set the Spiral Cutting	31
To set the level of Spiral Cutting	32
Slope control	32
To set the Slope control	32
General	32
To set the time & date	32
To set the language	32
To set the Country & Timezone	32
To set the unit format	32
To reset all user settings	32
The About menu	32
Accessories	33
Information	33
Automower® Connect app	33
To install the Automower® Connect app	33
Automower® Connect@Home	33
To pair Connect@Home and the product	33
To remove paired accounts	33
Automower® Connect	33
To pair Automower® Connect and the product	33
To enable the GeoFence function	34
To set a new center point for the Geofence function	34
To set the GeoFence level of sensitivity	34
To use the SMS function	34
Network	34
APN settings	34
Headlights Automower® 315X	34
To set the schedule for the headlights	34
To set the Flashes when fault function	34
To avoid collisions with the mower house	35
Operation	36
Main switch	36
To start the product	36
Operating mode Start	36
Main area	36
Secondary area	36
Override schedule	37
Spot cutting	37
Operating mode Park	37
Park until further notice	37
Start again with next schedule	37
To stop the product	37
To switch off the product	37
Schedule and Standby	37
Example 1	38
Example 2	38
To charge the battery	38
Adjust the cutting height	39
To adjust the cutting height	39
Maintenance	40
Introduction - maintenance	40
Clean the product	40
Chassis and blade disc	40
Wheels	40
The body of the product	40
Charging station	40
Replace the blades	41
To replace the blades	41
Battery	41
Winter service	42
Troubleshooting	43
Introduction - troubleshooting	43
Fault messages	43
Information messages	48
Indicator lamp in the charging station	49
Symptoms	50
Find breaks in the loop wire	51
Transportation, storage and disposal	54
Transportation	54
Storage	54
Disposal	54
To remove the battery	54
Technical data	55
Technical data	55
Registered trademarks	57
Warranty	58
Warranty terms	58
EC Declaration of Conformity	59

Match case Limit results 1 per page

Message

Cause

Action

Empty battery

The product cannot find the charging

station.

Change the position of the guide wire.

Refer to

To install the guide wire on

page 22

The battery is spent.

Replace the battery. Refer to

Battery

on page 41

The charging station’s antenna is de-

fective.

Check if the indicator lamp in the

charging station flashes red. Refer to

Indicator lamp in the charging station

on page 49

The charging plates on the product or

contact plates on the charging station

are corroded.

Clean the charging and contact plates

using a fine grade emery cloth. If the

problem stays speak to your authorized

service technician.

Wrong PIN code

Wrong PIN code has been entered.

Five attempts are permitted, and the

keypad is then blocked for a period of

time.

Enter the correct PIN code. Contact

Husqvarna customer service if you for-

get the PIN code.

No drive

The product has got caught in some-

thing and has been slipping.

Free the product and rectify the reason

for the lack of drive. If it is due to wet

grass, wait until the lawn has dried be-

fore using the product.

The work area includes a steep slope.

Steep slopes should be isolated. Refer

To put the boundary wire in a slope

on page 18

The guide wire is not laid diagonally in

the slope.

Make sure that the guide wire is instal-

led diagonally across the slope. Refer

To make a secondary area on page

Wheel motor over-

loaded, left/right

Grass or other object is wrapped

around the drive wheel.

Check the drive wheel and remove

grass or object.

Collision sensor

problem, front/rear

The product body can not move freely

around its chassis.

Check that the product body can move

freely around its chassis. If the problem

stays speak to your authorized service

technician.

Alarm! Mower

switched off

The alarm is activated because the

product had been switched off.

Adjust the security level in the

Security

menu. Refer to

To set the security level

on page 25

Alarm! Mower

stopped

The alarm is activated because the

product has been stopped.

Alarm! Mower lif-

ted

The alarm is activated because the

product has been lifted.

Alarm! Mower til-

ted

The alarm is activated because the

product has been tilted.

- Troubleshooting

1440 - 002 - 19.02.2020