Husqvarna AUTOMOWER 430XH Self-Install Owner Manual - Page 30

3.12.9.3 Corridor width

The boundary wire corridor is the area adjacent to

the boundary wire and the guide corridor is the area

adjacent to the guide wire. The product uses the

corridors to find the charging station. When the product

moves in the direction of the charging station, it always

moves to the left of the guide wire.

The corridor width is adjusted automatically. If it is

necessary to adjust the corridor width manually for the

product to operate satisfactorily, you can set the corridor

width between 0-9. If guide corridor width is set to 0, the

product straddles the guide wire. The factory setting is 6

for the boundary wire and 9 for the guide wire.

To set the corridor width

1.

Do steps 1–3 in

To get access to the menu in the

display of the product on page 22

.

2.

Use the

arrow

buttons and the

OK

button to move

through the menu structure

Installation > Advanced

> Corridor width

.

3.

Use the

arrow

buttons to select a corridor.

4.

Use the

number

buttons to select a corridor width

of 0-9.

Note:

Make the corridor width as wide as possible for

a minimum risk of lines in the lawn.

3.12.9.4 Exit angle

If the sum of the

Lawn Coverage

function is less than

100%, the product sometimes starts to mow at the

charging station. The product moves away from the

charging station with an exit angle between 90°–270°.

The exit angles can be set to 1–2 exit sectors.

To set the exit angle

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to move



> Exit angles > Sector 1

.

3.

Use the

number

buttons to set the angles in

degrees.

4.

Push the down

arrow

button.

5.

Use the

number

buttons to select how frequently

the product must use each sector. Set in

percentage.

6.

Push the

BACK

button.

3.12.9.5 Reversing distance

The reversing distance makes the product move in

reverse for a set distance, before the product starts to

cut the lawn. The factory setting is 60 cm / 2 ft.

To set the reversing distance

1.

Do steps 1-3 in



.

2.

Use the

arrow

button and the

OK

button to move



> Reversing distance

.

3.

Use the

number

buttons to set the distance.

4.

Push the

BACK

button.

3.12.9.6 Drive Past Wire function

The front of the product always moves past the

boundary wire by a specified distance. Then the product

moves rearward and changes direction. The factory

setting is 31 cm / 13 in. You can select a distance of

20-50 cm / 10-15 in.

Note:

If you change the distance for

Drive Past Wire

,

the distance will change along the boundary wire in all

parts of the work area.

To set the Drive Past Wire function

1.

Do steps 1–3 in



.

2.

Use the

arrow

button and the

OK

button to move



> Drive Past Wire

.

3.

Use the

number

buttons to set the distance.

4.

Push the

BACK

button.

3.12.10 Accessories

Settings for accessories mounted on the product can be

made in this menu.

3.12.10.1 Information

This menu handles accessories mounted on the

product. Contact your local Husqvarna representative for

more information on available accessories.

3.12.10.2 Automower

®

Connect

The product can connect to mobile devices that

have the Automower

®

Connect app installed. The

Automower

®

Connect app has Long-range cellular

30

- Installation

1230 - 004 - 04.03.2022

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview 1	7
Menu structure overview 2	8
Menu structure overview 3	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
Safety instructions for installation	12
Safety instructions for operation	12
Safety instructions for maintenance	12
Battery safety	12
How to lift and move the product	13
Installation	14
Introduction - Installation	14
Main components for installation	14
General preparations	14
Before the installation of the wires	14
To examine where to put the charging station	14
To examine where to put the power supply	15
To examine where to put the boundary wire	15
To put the boundary wire in a slope	16
Passages	17
To make an island	17
To make a secondary area	17
To examine where to put the guide wire	18
Work area examples	18
Installation of the product	19
Installation tools	19
To install the charging station	19
To install the boundary wire	19
To install the guide wire	20
To put the wire into position with stakes	20
To bury the boundary wire or the guide wire	21
To extend the boundary wire or the guide wire	21
After the installation of the product	21
To do a visual check of the charging station	21
To do the basic settings	21
Calibration	22
Product settings	22
Automower® Connect app	22
To install the Automower® Connect app	22
To pair Automower® Connect and the product	22
Product settings with keypad and display	22
To get access to the menu in the display of the product	22
Menu structure	22
Schedule	23
To set the schedule	23
To calculate the suitable operating hours	23
To copy the schedule setting	23
To reset the schedule setting	23
Cutting height	23
Adjust the cutting height	24
To set the cutting height	24
TargetHeight	24
To set the TargetHeight	24
Security level	24
To set the security level	24
To create a New loop signal	24
To change the PIN-code	24
To change the duration of the alarm	24
To change the duration of the time lock	25
Messages	25
To read the messages	25
Weather timer	25
To set the Weather timer	25
To set the Weather timer frequency	25
Settings	25
Profiles	26
To save settings to a profile	26
To change the name of a profile	26
To use a profile	26
To connect a new charging station to a profile	26
ECO mode	26
To set the ECO mode	26
Spiral Cutting	26
To set the Spiral Cutting	26
To set the level of Spiral Cutting	26
Slope control	27
To set the Slope control	27
General	27
To set the time & date	27
To set the language	27
To set the Country & Timezone	27
To set the unit format	27
To reset all user settings	27
The About menu	27
Installation	27
Lawn Coverage	27
GPS Assisted Navigation	28
To set the GPS Assisted Navigation	28
To set the Lawn Coverage function	28
To do a test of the Lawn Coverage function	28
To measure the distance from the charging station	28
To disable or enable the Lawn Coverage function	28
To reset the Lawn Coverage settings	28
Methods for the product to find the charging station	29
To set how the product finds the charging station	29
To do a test of the guide wire	29
To do a test of the boundary wire	29
To change the signal range of the charging station	29
Corridor width	30
To set the corridor width	30
Exit angle	30
To set the exit angle	30
Reversing distance	30
To set the reversing distance	30
Drive Past Wire function	30
To set the Drive Past Wire function	30
Accessories	30
Information	30
Automower® Connect	30
To enable the GeoFence function	31
To set a new center point for the Geofence function	31
To set the GeoFence level of sensitivity	31
To use the SMS function	31
Network	31
APN settings	31
Ultrasonic Automower® 450XH	31
To set the Ultrasonic function	31
Headlights	31
To set the schedule for the headlights	31
To set the Flashes when fault function	31
To avoid collisions with the Automower® house	32
FlexiFence	32
To enable the Zone generator function	32
Operation	33
Main switch	33
To start the product	33
Operating modes - Start	33
Main area	33
Secondary area	33
Override schedule	33
Spot cutting	34
To park the product	34
Operating modes - Park	34
Park until further notice	34
Start again with next schedule	34
To stop the product	34
To switch off the product	34
To charge the battery	34
Maintenance	35
Introduction - maintenance	35
Clean the product	35
Chassis and blade disc	35
To clean the wheels	35
To clean the body of the product	35
To clean the charging station	35
Replacement of the blades	36
To replace the blades	36
Battery	36
Winter service	36
Troubleshooting	37
Introduction - troubleshooting	37
Fault messages	37
Information messages	42
Indicator lamp in the charging station	44
Symptoms	45
Find breaks in the loop wire	46
Transportation, storage and disposal	49
Transportation	49
Storage	49
Disposal	49
To remove the battery	49
Technical data	50
Technical data	50
Registered trademarks	52
Warranty	53

Husqvarna AUTOMOWER 430XH Self-Install Owner Manual - Page 30

Accessories

Page 30 highlights