Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 430XH Self-Install » Manual Viewer

Husqvarna AUTOMOWER 430XH Self-Install Owner Manual - Page 42

Information messages

View all Husqvarna AUTOMOWER 430XH Self-Install manuals

Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Message Cause Action Zone generator problem FlexiFence problem The battery of the FlexiFence accessory is low. The FlexiFence accessory does not operate when the battery is empty. The product can cut in the stay-out zone if you start the product before you charge the FlexiFence accessory. Park the product and charge the FelxiFence accessory before you start the product. The temperature in the zone generator accessory is a higher than the maximum limit and is set to off. Put the product in an area with protection from the sun. Let the temperature of the zone generator accessory decrease before you start the product. Cutting system major imbalance The product has discovered vibrations in the blade disc Continued operation can cause damage to the cutting system. Examine that the blades and screws are not damaged or worn. Make sure that all blades are correctly installed and that there is only one blade attached in each position on the blade disc. 6.3 Information messages The list below shows a number of information messages that may be found in the Messages menu in the Automower® Connect app. Contact your local Husqvarna representative if the same message appears often. Message Low battery Cause Action The product cannot find the charging station. Change the position of the guide wire. Refer to To install the guide wire on page 20. Make sure that the installation settings about how to find the charging station is correct. Refer toMethods for the product to find the charging station on page 29. The battery is spent. Replace the battery. Refer to Battery on page 36. The charging station's antenna is defective. Check if the indicator lamp in the charging station flashes red. Refer to Methods for the product to find the charging station on page 29. This problem requires action by authorized service technician. Settings restored Confirmation that a Reset all user settings has been carried out. This is normal. No action required. Limited cutting height The cutting height adjustment cannot move. Unexpected cutting height adj Limited cutting height range Examine the cutting height adjustment and remove grass or other objects. If the problem stays, speak to your approved servicing dealer. Cutting height problem Cutting height blocked 42 - Troubleshooting 1230 - 004 - 04.03.2022

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview 1	7
Menu structure overview 2	8
Menu structure overview 3	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
Safety instructions for installation	12
Safety instructions for operation	12
Safety instructions for maintenance	12
Battery safety	12
How to lift and move the product	13
Installation	14
Introduction - Installation	14
Main components for installation	14
General preparations	14
Before the installation of the wires	14
To examine where to put the charging station	14
To examine where to put the power supply	15
To examine where to put the boundary wire	15
To put the boundary wire in a slope	16
Passages	17
To make an island	17
To make a secondary area	17
To examine where to put the guide wire	18
Work area examples	18
Installation of the product	19
Installation tools	19
To install the charging station	19
To install the boundary wire	19
To install the guide wire	20
To put the wire into position with stakes	20
To bury the boundary wire or the guide wire	21
To extend the boundary wire or the guide wire	21
After the installation of the product	21
To do a visual check of the charging station	21
To do the basic settings	21
Calibration	22
Product settings	22
Automower® Connect app	22
To install the Automower® Connect app	22
To pair Automower® Connect and the product	22
Product settings with keypad and display	22
To get access to the menu in the display of the product	22
Menu structure	22
Schedule	23
To set the schedule	23
To calculate the suitable operating hours	23
To copy the schedule setting	23
To reset the schedule setting	23
Cutting height	23
Adjust the cutting height	24
To set the cutting height	24
TargetHeight	24
To set the TargetHeight	24
Security level	24
To set the security level	24
To create a New loop signal	24
To change the PIN-code	24
To change the duration of the alarm	24
To change the duration of the time lock	25
Messages	25
To read the messages	25
Weather timer	25
To set the Weather timer	25
To set the Weather timer frequency	25
Settings	25
Profiles	26
To save settings to a profile	26
To change the name of a profile	26
To use a profile	26
To connect a new charging station to a profile	26
ECO mode	26
To set the ECO mode	26
Spiral Cutting	26
To set the Spiral Cutting	26
To set the level of Spiral Cutting	26
Slope control	27
To set the Slope control	27
General	27
To set the time & date	27
To set the language	27
To set the Country & Timezone	27
To set the unit format	27
To reset all user settings	27
The About menu	27
Installation	27
Lawn Coverage	27
GPS Assisted Navigation	28
To set the GPS Assisted Navigation	28
To set the Lawn Coverage function	28
To do a test of the Lawn Coverage function	28
To measure the distance from the charging station	28
To disable or enable the Lawn Coverage function	28
To reset the Lawn Coverage settings	28
Methods for the product to find the charging station	29
To set how the product finds the charging station	29
To do a test of the guide wire	29
To do a test of the boundary wire	29
To change the signal range of the charging station	29
Corridor width	30
To set the corridor width	30
Exit angle	30
To set the exit angle	30
Reversing distance	30
To set the reversing distance	30
Drive Past Wire function	30
To set the Drive Past Wire function	30
Accessories	30
Information	30
Automower® Connect	30
To enable the GeoFence function	31
To set a new center point for the Geofence function	31
To set the GeoFence level of sensitivity	31
To use the SMS function	31
Network	31
APN settings	31
Ultrasonic Automower® 450XH	31
To set the Ultrasonic function	31
Headlights	31
To set the schedule for the headlights	31
To set the Flashes when fault function	31
To avoid collisions with the Automower® house	32
FlexiFence	32
To enable the Zone generator function	32
Operation	33
Main switch	33
To start the product	33
Operating modes - Start	33
Main area	33
Secondary area	33
Override schedule	33
Spot cutting	34
To park the product	34
Operating modes - Park	34
Park until further notice	34
Start again with next schedule	34
To stop the product	34
To switch off the product	34
To charge the battery	34
Maintenance	35
Introduction - maintenance	35
Clean the product	35
Chassis and blade disc	35
To clean the wheels	35
To clean the body of the product	35
To clean the charging station	35
Replacement of the blades	36
To replace the blades	36
Battery	36
Winter service	36
Troubleshooting	37
Introduction - troubleshooting	37
Fault messages	37
Information messages	42
Indicator lamp in the charging station	44
Symptoms	45
Find breaks in the loop wire	46
Transportation, storage and disposal	49
Transportation	49
Storage	49
Disposal	49
To remove the battery	49
Technical data	50
Technical data	50
Registered trademarks	52
Warranty	53

Match case Limit results 1 per page

Message

Cause

Action

Zone generator prob-

lem

FlexiFence problem

The battery of the FlexiFence accessory is

low. The FlexiFence accessory does not op-

erate when the battery is empty. The product

can cut in the stay-out zone if you start the

product before you charge the FlexiFence

accessory.

Park the product and charge the FelxiFence

accessory before you start the product.

The temperature in the zone generator ac-

cessory is a higher than the maximum limit

and is set to off.

Put the product in an area with protection

from the sun. Let the temperature of the

zone generator accessory decrease before

you start the product.

Cutting system major

imbalance

The product has discovered vibrations in the

blade disc

Continued operation can cause damage to

the cutting system. Examine that the blades

and screws are not damaged or worn. Make

sure that all blades are correctly installed and

that there is only one blade attached in each

position on the blade disc.

6.3 Information messages

The list below shows a number of information messages that may be found in the

Messages

menu in the Automower

Connect app. Contact your local Husqvarna representative if the same message appears often.

Message

Cause

Action

Low battery

The product cannot find the charging station.

Change the position of the guide wire. Refer

To install the guide wire on page 20

Make sure that the installation settings about

how to find the charging station is correct.

Refer to

Methods for the product to find the

charging station on page 29

The battery is spent.

Replace the battery. Refer to

Battery on

page 36

The charging station’s antenna is defective.

Check if the indicator lamp in the charging

station flashes red. Refer to

Methods for the

product to find the charging station on page

. This problem requires action by author-

ized service technician.

Settings restored

Confirmation that a

Reset all user settings

has been carried out.

This is normal. No action required.

Limited cutting height

The cutting height adjustment cannot move.

Examine the cutting height adjustment and

remove grass or other objects. If the problem

stays, speak to your approved servicing deal-

er.

Unexpected cutting

height adj

Limited cutting height

range

Cutting height prob-

lem

Cutting height

blocked

- Troubleshooting

1230 - 004 - 04.03.2022