Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 430XH Self-Install » Manual Viewer

Husqvarna AUTOMOWER 430XH Self-Install Owner Manual - Page 44

Indicator lamp in the charging station

View all Husqvarna AUTOMOWER 430XH Self-Install manuals

Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Message SIM card requires PIN Cause The SIM card must be unlocked. Action Make sure the correct SIM PIN has been entered into the mower's menu (Network > SIM card). Contact your local Husqvarna representative if this message appears often. SIM card locked The SIM card must be replaced. Contact your local Husqvarna representative. SIM card not found Automower® Connect requires a SIM card to Contact your local Husqvarna representative. be inserted in the mower. GeoFence problem The is not work due to poor (or no) communi- Contact your local Husqvarna representative. cation with the system. Zone generator problem The battery of the FlexiFence accessory is low. The FlexiFence does not operate when the battery is empty. The product can cut in the stay-out zone if you start the product before you charge the FlexiFence. Park the product and charge the FlexiFence accessory before you start the product. The temperature in the FlexiFence accessory Put the product in an area with protection is a higher than the maximum limit and is set from the sun. Let the temperature of the to off. FlexiFence accessory decrease before you start the product. 6.4 Indicator lamp in the charging station The indicator lamp in the charging station must show a solid or flashing green light for a correct installation. If not, follow the instructions in the troubleshooting guide below. Speak to your Husqvarna customer service for more information. Light Cause Action Green solid light Good signals Usual operation of the product. Green flashing light The signals are good and ECO mode is ena- Usual operation of the product. Refer to ECO bled. mode on page 26. Blue flashing light The boundary wire is not connected to the charging station. Make sure that the boundary wire is correctly installed in the charging station. Refer to To install the boundary wire on page 19. Damage in the boundary wire. Find out where the damage is. Replace the damaged section with new boundary wire. Red flashing light Interference in the antenna of the charging station. Speak to your Husqvarna customer service. Red solid light Error in the circuit board or incorrect power Speak to your Husqvarna customer service. supply in the charging station. The error must be corrected by an authorized service technician. 44 - Troubleshooting 1230 - 004 - 04.03.2022

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview 1	7
Menu structure overview 2	8
Menu structure overview 3	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
Safety instructions for installation	12
Safety instructions for operation	12
Safety instructions for maintenance	12
Battery safety	12
How to lift and move the product	13
Installation	14
Introduction - Installation	14
Main components for installation	14
General preparations	14
Before the installation of the wires	14
To examine where to put the charging station	14
To examine where to put the power supply	15
To examine where to put the boundary wire	15
To put the boundary wire in a slope	16
Passages	17
To make an island	17
To make a secondary area	17
To examine where to put the guide wire	18
Work area examples	18
Installation of the product	19
Installation tools	19
To install the charging station	19
To install the boundary wire	19
To install the guide wire	20
To put the wire into position with stakes	20
To bury the boundary wire or the guide wire	21
To extend the boundary wire or the guide wire	21
After the installation of the product	21
To do a visual check of the charging station	21
To do the basic settings	21
Calibration	22
Product settings	22
Automower® Connect app	22
To install the Automower® Connect app	22
To pair Automower® Connect and the product	22
Product settings with keypad and display	22
To get access to the menu in the display of the product	22
Menu structure	22
Schedule	23
To set the schedule	23
To calculate the suitable operating hours	23
To copy the schedule setting	23
To reset the schedule setting	23
Cutting height	23
Adjust the cutting height	24
To set the cutting height	24
TargetHeight	24
To set the TargetHeight	24
Security level	24
To set the security level	24
To create a New loop signal	24
To change the PIN-code	24
To change the duration of the alarm	24
To change the duration of the time lock	25
Messages	25
To read the messages	25
Weather timer	25
To set the Weather timer	25
To set the Weather timer frequency	25
Settings	25
Profiles	26
To save settings to a profile	26
To change the name of a profile	26
To use a profile	26
To connect a new charging station to a profile	26
ECO mode	26
To set the ECO mode	26
Spiral Cutting	26
To set the Spiral Cutting	26
To set the level of Spiral Cutting	26
Slope control	27
To set the Slope control	27
General	27
To set the time & date	27
To set the language	27
To set the Country & Timezone	27
To set the unit format	27
To reset all user settings	27
The About menu	27
Installation	27
Lawn Coverage	27
GPS Assisted Navigation	28
To set the GPS Assisted Navigation	28
To set the Lawn Coverage function	28
To do a test of the Lawn Coverage function	28
To measure the distance from the charging station	28
To disable or enable the Lawn Coverage function	28
To reset the Lawn Coverage settings	28
Methods for the product to find the charging station	29
To set how the product finds the charging station	29
To do a test of the guide wire	29
To do a test of the boundary wire	29
To change the signal range of the charging station	29
Corridor width	30
To set the corridor width	30
Exit angle	30
To set the exit angle	30
Reversing distance	30
To set the reversing distance	30
Drive Past Wire function	30
To set the Drive Past Wire function	30
Accessories	30
Information	30
Automower® Connect	30
To enable the GeoFence function	31
To set a new center point for the Geofence function	31
To set the GeoFence level of sensitivity	31
To use the SMS function	31
Network	31
APN settings	31
Ultrasonic Automower® 450XH	31
To set the Ultrasonic function	31
Headlights	31
To set the schedule for the headlights	31
To set the Flashes when fault function	31
To avoid collisions with the Automower® house	32
FlexiFence	32
To enable the Zone generator function	32
Operation	33
Main switch	33
To start the product	33
Operating modes - Start	33
Main area	33
Secondary area	33
Override schedule	33
Spot cutting	34
To park the product	34
Operating modes - Park	34
Park until further notice	34
Start again with next schedule	34
To stop the product	34
To switch off the product	34
To charge the battery	34
Maintenance	35
Introduction - maintenance	35
Clean the product	35
Chassis and blade disc	35
To clean the wheels	35
To clean the body of the product	35
To clean the charging station	35
Replacement of the blades	36
To replace the blades	36
Battery	36
Winter service	36
Troubleshooting	37
Introduction - troubleshooting	37
Fault messages	37
Information messages	42
Indicator lamp in the charging station	44
Symptoms	45
Find breaks in the loop wire	46
Transportation, storage and disposal	49
Transportation	49
Storage	49
Disposal	49
To remove the battery	49
Technical data	50
Technical data	50
Registered trademarks	52
Warranty	53

Match case Limit results 1 per page

Message

Cause

Action

SIM card requires

The SIM card must be unlocked.

Make sure the correct SIM PIN has been

entered into the mower's menu (Network >

SIM card). Contact your local Husqvarna rep-

resentative if this message appears often.

SIM card locked

The SIM card must be replaced.

Contact your local Husqvarna representative.

SIM card not found

Automower

Connect requires a SIM card to

be inserted in the mower.

Contact your local Husqvarna representative.

GeoFence problem

The is not work due to poor (or no) communi-

cation with the system.

Contact your local Husqvarna representative.

Zone generator prob-

lem

The battery of the FlexiFence accessory is

low. The FlexiFence does not operate when

the battery is empty. The product can cut

in the stay-out zone if you start the product

before you charge the FlexiFence.

Park the product and charge the FlexiFence

accessory before you start the product.

The temperature in the FlexiFence accessory

is a higher than the maximum limit and is set

to off.

Put the product in an area with protection

from the sun. Let the temperature of the

FlexiFence accessory decrease before you

start the product.

6.4 Indicator lamp in the charging station

The indicator lamp in the charging station must show a solid or flashing green light for a correct installation. If not,

follow the instructions in the troubleshooting guide below.

Speak to your Husqvarna customer service for more information.

Light

Cause

Action

Green solid light

Good signals

Usual operation of the product.

Green flashing light

The signals are good and

ECO mode

is ena-

bled.

Usual operation of the product. Refer to

ECO

mode on page 26

Blue flashing light

The boundary wire is not connected to the

charging station.

Make sure that the boundary wire is correctly

installed in the charging station. Refer to

install the boundary wire on page 19

Damage in the boundary wire.

Find out where the damage is. Replace the

damaged section with new boundary wire.

Red flashing light

Interference in the antenna of the charging

station.

Speak to your Husqvarna customer service.

Red solid light

Error in the circuit board or incorrect power

supply in the charging station. The error must

be corrected by an authorized service techni-

cian.

Speak to your Husqvarna customer service.

- Troubleshooting

1230 - 004 - 04.03.2022