Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 430XH Self-Install » Manual Viewer

Husqvarna AUTOMOWER 430XH Self-Install Owner Manual - Page 43

Weak GPS signal

View all Husqvarna AUTOMOWER 430XH Self-Install manuals

Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Message Cause Cutting system imbal- The product has discovered vibrations in the ance blade disc. Action Verify that the blades and screws are intact and not worn out. Verify that all blades are correctly mounted. Check that no double blades are mounted on any of the three blade positions. Slope too steep The product stopped because the slope is too steep. Change the installation of the boundary wire to not include this steep part of the work area. Refer to To install the boundary wire on page 19. Guide 1 not found Guide 2 not found Guide 3 not found The guide wire is not connected to the charg- Check that the guide wire's connector is ing station. tightly connected to the charging station. Re- fer to To install the guide wire on page 20. Break in the guide wire. Find out where the break is. Replace the damaged section of the guide wire with a new loop wire and splice using an original coupler. The guide wire is not connected to the boun- Check that the guide wire is connected cor- dary loop. rectly to the boundary loop. Refer to To install the guide wire on page 20. Guide calibration failed The product has failed to calibrate the guide wire. Check that the guide wires are installed according to the instructions. Refer to To install the guide wire on page 20. The next time the product moves out from the charging station, a new guide calibration is done. Guide calibration ac- The product has succeeded to calibrate the No action required. complished guide wire. GPS navigation prob- Problem with the GPS assisted navigation lem equipment. Contact your local Husqvarna representative if this message appears often. Weak GPS signal The sky is blocked in large parts of the work If possible, remove objects that can cause a area. blockage of the GPS signal. Disable the GPS navigation function and use the lawn coverage function. Refer to To set the Lawn Coverage function on page 28. Difficult finding home The product has been following the boundary The installation has not been done correctly. wire several laps without finding the charging Refer to Methods for the product to find the station. charging station on page 29. Wrong corridor width setting on boundary wire. Refer to To install the boundary wire on page 19. The product was started on a Secondary area with the Main area setting. Temporary problem Please try again. with the server. Contact your local Husqvarna representative if this message appears often. Connection settings Settings for wireless connectivity have been Check and revise settings if necessary. restored restored due to an error. 1230 - 004 - 04.03.2022 Troubleshooting - 43

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview 1	7
Menu structure overview 2	8
Menu structure overview 3	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
Safety instructions for installation	12
Safety instructions for operation	12
Safety instructions for maintenance	12
Battery safety	12
How to lift and move the product	13
Installation	14
Introduction - Installation	14
Main components for installation	14
General preparations	14
Before the installation of the wires	14
To examine where to put the charging station	14
To examine where to put the power supply	15
To examine where to put the boundary wire	15
To put the boundary wire in a slope	16
Passages	17
To make an island	17
To make a secondary area	17
To examine where to put the guide wire	18
Work area examples	18
Installation of the product	19
Installation tools	19
To install the charging station	19
To install the boundary wire	19
To install the guide wire	20
To put the wire into position with stakes	20
To bury the boundary wire or the guide wire	21
To extend the boundary wire or the guide wire	21
After the installation of the product	21
To do a visual check of the charging station	21
To do the basic settings	21
Calibration	22
Product settings	22
Automower® Connect app	22
To install the Automower® Connect app	22
To pair Automower® Connect and the product	22
Product settings with keypad and display	22
To get access to the menu in the display of the product	22
Menu structure	22
Schedule	23
To set the schedule	23
To calculate the suitable operating hours	23
To copy the schedule setting	23
To reset the schedule setting	23
Cutting height	23
Adjust the cutting height	24
To set the cutting height	24
TargetHeight	24
To set the TargetHeight	24
Security level	24
To set the security level	24
To create a New loop signal	24
To change the PIN-code	24
To change the duration of the alarm	24
To change the duration of the time lock	25
Messages	25
To read the messages	25
Weather timer	25
To set the Weather timer	25
To set the Weather timer frequency	25
Settings	25
Profiles	26
To save settings to a profile	26
To change the name of a profile	26
To use a profile	26
To connect a new charging station to a profile	26
ECO mode	26
To set the ECO mode	26
Spiral Cutting	26
To set the Spiral Cutting	26
To set the level of Spiral Cutting	26
Slope control	27
To set the Slope control	27
General	27
To set the time & date	27
To set the language	27
To set the Country & Timezone	27
To set the unit format	27
To reset all user settings	27
The About menu	27
Installation	27
Lawn Coverage	27
GPS Assisted Navigation	28
To set the GPS Assisted Navigation	28
To set the Lawn Coverage function	28
To do a test of the Lawn Coverage function	28
To measure the distance from the charging station	28
To disable or enable the Lawn Coverage function	28
To reset the Lawn Coverage settings	28
Methods for the product to find the charging station	29
To set how the product finds the charging station	29
To do a test of the guide wire	29
To do a test of the boundary wire	29
To change the signal range of the charging station	29
Corridor width	30
To set the corridor width	30
Exit angle	30
To set the exit angle	30
Reversing distance	30
To set the reversing distance	30
Drive Past Wire function	30
To set the Drive Past Wire function	30
Accessories	30
Information	30
Automower® Connect	30
To enable the GeoFence function	31
To set a new center point for the Geofence function	31
To set the GeoFence level of sensitivity	31
To use the SMS function	31
Network	31
APN settings	31
Ultrasonic Automower® 450XH	31
To set the Ultrasonic function	31
Headlights	31
To set the schedule for the headlights	31
To set the Flashes when fault function	31
To avoid collisions with the Automower® house	32
FlexiFence	32
To enable the Zone generator function	32
Operation	33
Main switch	33
To start the product	33
Operating modes - Start	33
Main area	33
Secondary area	33
Override schedule	33
Spot cutting	34
To park the product	34
Operating modes - Park	34
Park until further notice	34
Start again with next schedule	34
To stop the product	34
To switch off the product	34
To charge the battery	34
Maintenance	35
Introduction - maintenance	35
Clean the product	35
Chassis and blade disc	35
To clean the wheels	35
To clean the body of the product	35
To clean the charging station	35
Replacement of the blades	36
To replace the blades	36
Battery	36
Winter service	36
Troubleshooting	37
Introduction - troubleshooting	37
Fault messages	37
Information messages	42
Indicator lamp in the charging station	44
Symptoms	45
Find breaks in the loop wire	46
Transportation, storage and disposal	49
Transportation	49
Storage	49
Disposal	49
To remove the battery	49
Technical data	50
Technical data	50
Registered trademarks	52
Warranty	53

Match case Limit results 1 per page

Message

Cause

Action

Cutting system imbal-

ance

The product has discovered vibrations in the

blade disc.

Verify that the blades and screws are in-

tact and not worn out. Verify that all blades

are correctly mounted. Check that no dou-

ble blades are mounted on any of the three

blade positions.

Slope too steep

The product stopped because the slope is

too steep.

Change the installation of the boundary wire

to not include this steep part of the work

area. Refer to

To install the boundary wire

on page 19

Guide 1 not found

Guide 2 not found

Guide 3 not found

The guide wire is not connected to the charg-

ing station.

Check that the guide wire’s connector is

tightly connected to the charging station. Re-

fer to

To install the guide wire on page 20

Break in the guide wire.

Find out where the break is. Replace the

damaged section of the guide wire with a

new loop wire and splice using an original

coupler.

The guide wire is not connected to the boun-

dary loop.

Check that the guide wire is connected cor-

rectly to the boundary loop. Refer to

To in-

stall the guide wire on page 20

Guide calibration

failed

The product has failed to calibrate the guide

wire.

Check that the guide wires are installed ac-

cording to the instructions. Refer to

To install

the guide wire on page 20

. The next time the

product moves out from the charging station,

a new guide calibration is done.

Guide calibration ac-

complished

The product has succeeded to calibrate the

guide wire.

No action required.

GPS navigation prob-

lem

Problem with the GPS assisted navigation

equipment.

Contact your local Husqvarna representative

if this message appears often.

Weak GPS signal

The sky is blocked in large parts of the work

area.

If possible, remove objects that can cause a

blockage of the GPS signal.

Disable the GPS navigation function and use

the lawn coverage function. Refer to

To set

the Lawn Coverage function on page 28

Difficult finding home

The product has been following the boundary

wire several laps without finding the charging

station.

The installation has not been done correctly.

Refer to

Methods for the product to find the

charging station on page 29

Wrong corridor width setting on boundary

wire. Refer to

To install the boundary wire on

page 19

The product was started on a Secondary

area with the Main area setting.

Temporary problem

with the server.

Please try again.

Contact your local Husqvarna representative

if this message appears often.

Connection settings

restored

Settings for wireless connectivity have been

restored due to an error.

Check and revise settings if necessary.

1230 - 004 - 04.03.2022

Troubleshooting -