Husqvarna AUTOMOWER 430XH Self-Install Owner Manual - Page 31

connectivity and Short-range Bluetooth

®

connectivity.

Refer to

Automower

®

Connect app on page 22

.

Note:

Automower

®

Connect is always connected to

your product while the mobile device have connection

with the mobile network and the product is switched on.

Note:

All countries do not support Automower

®

Connect because of regional specified cellular systems.

The included Automower

®

Connect life-time service only

applies if there is a third part sub-supplier of 2G/3G/4G

available in the operational area. In some countries

Bluetooth

®

is not available because of legal reasons.

To enable the GeoFence function

GeoFence is a GPS-based theft protection that makes a

virtual fence for the product. You will get a message if

the product is moved on the other side of the GeoFence.

1.

Put the product in the center of the work area.

2.

Do steps 1–3 in

To get access to the menu in the

display of the product on page 22

.

3.

Use the

arrow buttons

and the

OK

button to

move through the menu structure

Accessories

> Automower Connect > GeoFence > Activate

GeoFence

.

4.

Push the

OK

button.

5.

Select

Activate GeoFence

and push the

OK

button.

To set a new center point for the Geofence function

1.

Put the product in the center of the work area.

2.

Do steps 1–3 in



.

3.

Use the

arrow buttons

and the

OK

button to


Accessories >

Automower Connect > GeoFence > New center

point

.

4.

Push the

OK

button.

To set the GeoFence level of sensitivity

The higher level of GeoFence sensitivity, the easier the

alarm starts.

1.

Do steps 1–3 in



.

2.

Use the

arrow buttons

and the

OK

button to


Accessories >

Automower Connect > GeoFence

.

3.

Use the

arrow buttons

to select level of GeoFence

sensitivity.

4.

Push the

BACK

button.

To use the SMS function

The SMS function sends you an SMS when the product

is moved out of the GeoFence.

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to


Accessories

> Automower Connect > Communication > Use

SMS

.

3.

Push the

OK

button.

4.

Use the

arrow

buttons and the

OK

button to


Accessories >

Automower Connect > Communication > SMS

phone numbers

.

5.

Push the

number

buttons to enter the telephone

number with country code. For example

(+)46701234567.

6.

Push the

BACK

button.

Note:

There is a maximum of 10 SMS each month

from the product.

Network

APN settings

The product must specify APN settings to be able to

use and send data via the mobile net. Settings for

Husqvarna SIM is default.

3.12.10.3 Ultrasonic Automower

®

450XH

The

Ultrasonic

function makes the product decrease

speed when the product comes near an obstacle. The

product operates at a lower speed if the

Ultrasonic

function is disabled.

To set the Ultrasonic function

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to


Accessories >

Ultrasonic > Use

.

3.12.10.4 Headlights

To set the schedule for the headlights

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to


Accessories >

Headlights > Schedule

.

3.

Select between

Always ON

,

Evening only

(19:00-00:00),

Evening & night

(19:00-07:00) or

Always OFF

.

To set the Flashes when fault function

The headlights flashes if the product stops to operate

because of a fault if

Flashes when fault

is enabled.

1.

Do steps 1–3 in



.

2.

Use the

arrow

buttons and the

OK

button to


Accessories >

Headlights > Flashes when fault

.

1230 - 004 - 04.03.2022

Installation -

31

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Mowing technique	3
Find the charging station	3
Automower® Connect	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols on the display	5
Symbols on the battery	6
General manual instructions	6
Menu structure overview 1	7
Menu structure overview 2	8
Menu structure overview 3	9
Display	10
Keypad	10
Safety	11
Safety definitions	11
General safety instructions	11
Safety instructions for installation	12
Safety instructions for operation	12
Safety instructions for maintenance	12
Battery safety	12
How to lift and move the product	13
Installation	14
Introduction - Installation	14
Main components for installation	14
General preparations	14
Before the installation of the wires	14
To examine where to put the charging station	14
To examine where to put the power supply	15
To examine where to put the boundary wire	15
To put the boundary wire in a slope	16
Passages	17
To make an island	17
To make a secondary area	17
To examine where to put the guide wire	18
Work area examples	18
Installation of the product	19
Installation tools	19
To install the charging station	19
To install the boundary wire	19
To install the guide wire	20
To put the wire into position with stakes	20
To bury the boundary wire or the guide wire	21
To extend the boundary wire or the guide wire	21
After the installation of the product	21
To do a visual check of the charging station	21
To do the basic settings	21
Calibration	22
Product settings	22
Automower® Connect app	22
To install the Automower® Connect app	22
To pair Automower® Connect and the product	22
Product settings with keypad and display	22
To get access to the menu in the display of the product	22
Menu structure	22
Schedule	23
To set the schedule	23
To calculate the suitable operating hours	23
To copy the schedule setting	23
To reset the schedule setting	23
Cutting height	23
Adjust the cutting height	24
To set the cutting height	24
TargetHeight	24
To set the TargetHeight	24
Security level	24
To set the security level	24
To create a New loop signal	24
To change the PIN-code	24
To change the duration of the alarm	24
To change the duration of the time lock	25
Messages	25
To read the messages	25
Weather timer	25
To set the Weather timer	25
To set the Weather timer frequency	25
Settings	25
Profiles	26
To save settings to a profile	26
To change the name of a profile	26
To use a profile	26
To connect a new charging station to a profile	26
ECO mode	26
To set the ECO mode	26
Spiral Cutting	26
To set the Spiral Cutting	26
To set the level of Spiral Cutting	26
Slope control	27
To set the Slope control	27
General	27
To set the time & date	27
To set the language	27
To set the Country & Timezone	27
To set the unit format	27
To reset all user settings	27
The About menu	27
Installation	27
Lawn Coverage	27
GPS Assisted Navigation	28
To set the GPS Assisted Navigation	28
To set the Lawn Coverage function	28
To do a test of the Lawn Coverage function	28
To measure the distance from the charging station	28
To disable or enable the Lawn Coverage function	28
To reset the Lawn Coverage settings	28
Methods for the product to find the charging station	29
To set how the product finds the charging station	29
To do a test of the guide wire	29
To do a test of the boundary wire	29
To change the signal range of the charging station	29
Corridor width	30
To set the corridor width	30
Exit angle	30
To set the exit angle	30
Reversing distance	30
To set the reversing distance	30
Drive Past Wire function	30
To set the Drive Past Wire function	30
Accessories	30
Information	30
Automower® Connect	30
To enable the GeoFence function	31
To set a new center point for the Geofence function	31
To set the GeoFence level of sensitivity	31
To use the SMS function	31
Network	31
APN settings	31
Ultrasonic Automower® 450XH	31
To set the Ultrasonic function	31
Headlights	31
To set the schedule for the headlights	31
To set the Flashes when fault function	31
To avoid collisions with the Automower® house	32
FlexiFence	32
To enable the Zone generator function	32
Operation	33
Main switch	33
To start the product	33
Operating modes - Start	33
Main area	33
Secondary area	33
Override schedule	33
Spot cutting	34
To park the product	34
Operating modes - Park	34
Park until further notice	34
Start again with next schedule	34
To stop the product	34
To switch off the product	34
To charge the battery	34
Maintenance	35
Introduction - maintenance	35
Clean the product	35
Chassis and blade disc	35
To clean the wheels	35
To clean the body of the product	35
To clean the charging station	35
Replacement of the blades	36
To replace the blades	36
Battery	36
Winter service	36
Troubleshooting	37
Introduction - troubleshooting	37
Fault messages	37
Information messages	42
Indicator lamp in the charging station	44
Symptoms	45
Find breaks in the loop wire	46
Transportation, storage and disposal	49
Transportation	49
Storage	49
Disposal	49
To remove the battery	49
Technical data	50
Technical data	50
Registered trademarks	52
Warranty	53

Husqvarna AUTOMOWER 430XH Self-Install Owner Manual - Page 31

> Automower Connect > GeoFence > Activate

Page 31 highlights