Husqvarna AUTOMOWER 550H Owner Manual - Page 18

To examine where to put the guide wire, Work area examples, Lawn Coverage

Get Husqvarna AUTOMOWER 550H PDF manuals and user guides View all Husqvarna AUTOMOWER 550H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

3.3.5 Work area examples B D A A Note: When the product cuts grass in the secondary area, the Secondary area mode must be selected. Refer to Secondary area B on page 31. 3.3.4 To examine where to put the guide wire • Put the guide wire in a line at a minimum of 2 m / 7 ft. in front of the charging station. • Make sure that the guide wire has as much free area as possible to the left of the guide wire when facing the charging station. Refer to To set the corridor width of the guide wire on page 26. • Put the guide wire minimum 30 cm / 12 in. from the boundary wire. • Do not make sharp bends when you install the guide wire. • If the work area has a slope, put the guide wire diagonally across the slope. C • If the charging station is put in a small area (A), make sure that the distance to the boundary wire is at a minimum 3 m / 10 ft. • If the work area has a passage (B), make sure that the distance to the boundary wire is at a minimum 2 m / 6.5 ft. If the passage is smaller than 2 m / 6.5 ft., install a guide wire through the passage. Minimum passage between the boundary wire is 60 cm / 24 in. • If the work area has areas which are connected by small passages (C), change the settings in Lawn Coverage. Refer to Lawn coverage on page 25. • Use the GPS Assisted Navigation. Refer to Lawn coverage on page 25. • If the work area includes a secondary area (D), refer to To make a secondary area on page 17. Put the product in the secondary area and select Secondary area mode. Refer to Secondary area on page 31. 18 - Installation 1102 - 002 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
B
A
Note:
When the product cuts grass in the
secondary area, the
Secondary area
mode
must be selected. Refer to
Secondary area
on page 31
.
3.3.4 To examine where to put the guide
wire
•
Put the guide wire in a line at a minimum of
2 m / 7 ft. in front of the charging station.
•
Make sure that the guide wire has as much
free area as possible to the left of the guide
wire when facing the charging station. Refer
to
To set the corridor width of the guide wire
on page 26
.
•
Put the guide wire minimum 30 cm / 12 in.
from the boundary wire.
•
Do not make sharp bends when you install
the guide wire.
•
If the work area has a slope, put the guide
wire diagonally across the slope.
3.3.5 Work area examples
B
D
A
C
•
If the charging station is put in a small area
(A), make sure that the distance to the
boundary wire is at a minimum 3 m / 10 ft.
•
If the work area has a passage (B), make
sure that the distance to the boundary wire
is at a minimum 2 m / 6.5 ft. If the passage is
smaller than 2 m / 6.5 ft., install a guide wire
through the passage. Minimum passage
between the boundary wire is 60 cm / 24 in.
•
If the work area has areas which are
connected by small passages (C), change
the settings in
Lawn Coverage
. Refer to
Lawn coverage on page 25
.
•
Use the GPS Assisted Navigation. Refer to
Lawn coverage on page 25
.
•
If the work area includes a secondary area
(D), refer to
To make a secondary area on
page 17
. Put the product in the secondary
area and select
Secondary area mode
.
Refer to
Secondary area on page 31
.
18
- Installation
1102 - 002 -