Husqvarna AUTOMOWER 550H Owner Manual - Page 26

find the charging station. When the product

moves in the direction of the charging station, it

always moves to the left of the boundary wire.

The boundary corridor width is specified in

intervals from 1-9. The first number in the interval

specifies the shortest distance to the boundary

loop and the second number the longest

distance. The distance the product maintains

from the boundary loop varies depending on the

layout of the work area. The default setting is 3-6.

1.

Slide the horizontal bar to specify the

required interval.

3.16.4.2 To set the corridor width of the guide

wire

The guide corridor is the area adjacent to the

guide wire, which the product uses to find the

charging station. When the product moves in the

direction of the charging station, it always moves

to the left of the guide wire.

The guide corridor width is adjusted

automatically. Only in rare occasions manual

settings need to be entered. The guide corridor

width can be set between 0 and 9. If guide

corridor width is set to 0, the product straddles

the guide wire. This means that the product runs

right over the guide wire. The default setting is 9.

1.


required value.

Note:

Make the corridor width as wide as

possible for a minimum risk of lines in the lawn.

3.16.5 Exit angles

Normally the product leaves the charging station

in a direction within the 90°-270° exit sector. By

changing the exit angles, it makes it easier for the

product to reach the work areas.

3.16.5.1 Exit angles > Sectors

The product can be set for 1 or 2 exit sectors. If

the charging station is placed in a passage, 2 exit

angles, for instance 70° - 110° and 250° - 290°,

can be used.

When 2 exit angles are used, there is a need to

also specify how often the product must leave the

charging station in

Sector 1

. This is done using

the

Proportion

function by initially specifying a

percentage.

For instance the percentage of 75 % means that

the product leaves the charging station in

Sector

1

on 75% of the times and 25% of the times in

Sector 2

.

1.


required angles in degrees for the sectors,

and proportion as a percentage.

3.16.6 To set the reversing distance

The reversing distance makes the product move

in reverse for a set amount of cm before the

product starts to cut the lawn. The default setting

is 60 cm.

1.


required reversing distance.

3.16.7 To set the Drive Past Wire function

The front of the product always moves past the

boundary wire by a specified distance before the

product moves back into the work area. The

factory setting is 31 cm. You can select a

distance of 20 cm and 50 cm.

1.

Slide the horizontal bar to specify how much

the product should pass the boundary wire.

3.17 Accessories

Settings for accessories mounted on

the product can be made in this menu.

3.17.1 Mower house

When this option is enabled, the wear on the

product and the house is reduced, but it can

result in more uncut grass around the charging

station.

26

- Installation

1102 - 002 -

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols in Automower® Connect	6
Symbols on the battery	6
Overview of the settings structure (1)	7
Overview of the settings structure (2)	8
Overview of the settings structure (3) (Bluetooth® short-range connectivity only)	9
Safety	10
Safety definitions	10
General safety instructions	10
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	11
Safety instructions for operation	12
Use	12
Battery safety	13
How to lift and move the product	13
Maintenance	14
In the event of a thunderstorm	14
Installation	15
Introduction - Installation	15
Before the installation of the wires	15
Before the installation of the product	15
To examine where to put the charging station	15
To examine where to put the power supply	16
To examine where to put the boundary wire	16
To put the boundary wire in a slope	17
Passages	17
To make an island	17
To make a secondary area	17
To examine where to put the guide wire	18
Work area examples	18
Installation of the product	19
To install the charging station	19
To install the boundary wire	19
To install the guide wire	20
To put the wire into position with stakes	20
To bury the boundary wire or the guide wire	20
To change the position of the boundary wire or the guide wire	20
To extend the boundary wire or the guide wire	21
After the installation of the product	21
To do a visual check of the charging station	21
To start the product for the first time	21
Automower® Connect	21
To install Automower® Connect	22
To pair Automower® Connect and the product	22
Automower® Connect menu	22
Dashboard	22
Map	22
Map settings	22
Settings in Automower® Connect	22
Timer settings	22
To calculate the timer setting	23
Edit timer settings	23
Edit current timer settings	23
Add a new timer setting	23
Cutting height	23
To set the cutting height	23
Operation	23
Weather timer	23
ECO mode	24
Spiral cutting	24
Installation	24
Methods for the product to find the charging station	24
Finding the charging station	25
Lawn coverage	25
To disable and enable the GPS function	25
Area 1-5 > Enable/disable	25
Area 1-5 > How? and How far?	25
Area 1-5 > How often?	25
Corridor width	25
To set the corridor width of the boundary wire	25
To set the corridor width of the guide wire	26
Exit angles	26
Exit angles > Sectors	26
To set the reversing distance	26
To set the Drive Past Wire function	26
Accessories	26
Mower house	26
Ultrasonic	27
General (Bluetooth® only)	27
Time & Date	27
To reset to factory settings	27
Security (Bluetooth® only)	27
To create a new loop signal	27
Change PIN code	27
Theft protection	27
Alarm duration	27
Lifted	27
Turned upside down	27
STOP button pressed	27
Time lock	28
GeoFence	28
Automower® Connect (Bluetooth® only)	28
Messages (Bluetooth® only)	28
My mowers	28
Automower® Direct	28
To start to use Automower® Direct	29
Husqvarna Fleet Services™	29
To connect to the product with Husqvarna Fleet Services™	29
Operation	30
Main switch	30
Start	30
Operating mode - Start	30
Main area	30
Override timer	30
Secondary area	31
Operating mode - Park	31
Park until further notice	31
Start on next timer	31
Parking duration	31
The charging station's park button	31
Operating mode - Pause	31
Stop	31
Switch off	31
Charge a flat battery	32
Maintenance	33
Introduction - maintenance	33
Clean the product	33
Chassis and blade disc	33
Chassis	33
Wheels	33
Cover	33
Charging station	33
Replace the blades	34
To replace the blades	34
Battery	34
Winter service	35
Troubleshooting	36
Introduction - troubleshooting	36
Fault messages	36
Information messages	41
LED indicator lamp on the charging station	43
LED indicator lamp on the product	44
Symptoms	45
Finding breaks in the loop wire	46
Transportation, storage and disposal	49
Transportation	49
Storage	49
Disposal	49
To remove the battery	49
Technical data	50
Technical data	50
Registered trademarks	52
Warranty	53
Guarantee terms	53
Applicable to US/CA market	54
Supplier's Declaration of Conformity	54

Husqvarna AUTOMOWER 550H Owner Manual - Page 26

To set the corridor width of the guide wire, Exit angles, Exit angles > Sectors

Page 26 highlights