Husqvarna AUTOMOWER 550H Owner Manual - Page 25

Finding the charging station, Lawn coverage, To disable and enable the GPS function, Area 1-5 >

Get Husqvarna AUTOMOWER 550H PDF manuals and user guides View all Husqvarna AUTOMOWER 550H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

You can change the settings for how the product finds the charging station to adapt to the work area. 3.16.2 Finding the charging station The product can be set to search for the charging station in one or more of the following three ways: 1. Charging station signal 2. Follow boundary wire 3. Follow guide wire The default settings are set so that these 3 search options are combined to find the charging station as fast as possible, but also with a minimum risk of tracks forming on the lawn. The product always starts by searching for the Charging station signal. After a specified time delay, it also uses Follow guide and Follow boundary wire. Common causes why the product cannot follow the wire are: • Obstacles close to the wire have not been isolated. • The charging station, the boundary wire or the guide wire is not installed in accordance with the instructions in To install the charging station on page 19, To install the boundary wire on page 19 and in To install the guide wire on page 20. 3.16.3 Lawn coverage The product has GPS Assisted Navigation that helps the product select the most optimal operation. In more complex gardens operation can be improved by carrying out some of the manual settings in the Lawn coverage menu. 3.16.3.1 To disable and enable the GPS function Disable the GPS Assisted Navigation to make manual settings in Lawn Coverage. Note: It is recommended to use GPS Assisted Navigation. 1. Select GPS assisted navigation. 2. Tap the On/Off to enable or disable GPS assisted navigation. Note: When GPS assisted navigation is enabled it is used as long as there is a GPS service. The GPS assisted navigation is used even if manual settings have been made. Only when GPS service is not available, the manual settings are used. 3.16.3.2 Area 1-5 > Enable/disable Each area can be enabled/disabled, without having to reenter the settings. 1. Tap the On/Off bar for Area 1-5. 3.16.3.3 Area 1-5 > How? and How far? Specify to the right, left or Guide depending on which direction the product should go. The direction (left or right) is when facing the charging station. 1. Slide the horizontal bar to alternate between Lawn coverage settings. 2. Slide the horizontal bar to change the distance. The default settings let the product follow the guide wire 300 m / 328 yd. in 20% of the times it leaves the charging station. If the guide wire in reality is less than 300 m / 328 yd. the product will follow it to the point where the guide wire is connected to the boundary wire. 3.16.3.4 Area 1-5 > How often? How often the product should go to the remote area is selected as a proportion of the total number of times it leaves the charging station. At all other times, the products starts to mow close to the charging station. Select the percentage that corresponds to the size of the remote area relative to the total work area. If the remote area is for instance half of the total work area, 50% should be selected. A lower figure should be specified if the remote area is smaller. If more areas are used, take into account that the total figure cannot exceed 100%. 1. Slide the horizontal bar to change the percentage. 3.16.4 Corridor width 3.16.4.1 To set the corridor width of the boundary wire The boundary wire corridor is the area adjacent to the boundary wire, which the product uses to 1102 - 002 - Installation - 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
You can change the settings for how the product
finds the charging station to adapt to the work
area.
3.16.2 Finding the charging station
The product can be set to search for the charging
station in one or more of the following three
ways:
1.
Charging station signal
2.
Follow boundary wire
3.
Follow guide wire
The default settings are set so that these 3
search options are combined to find the charging
station as fast as possible, but also with a
minimum risk of tracks forming on the lawn. The
product always starts by searching for the
Charging station signal
. After a specified time
delay, it also uses
Follow guide
and
Follow
boundary wire
.
Common causes why the product cannot follow
the wire are:
•
Obstacles close to the wire have not been
isolated.
•
The charging station, the boundary wire or
the guide wire is not installed in accordance
with the instructions in
To install the
charging station on page 19
,
To install the
boundary wire on page 19
and in
To install
the guide wire on page 20
.
3.16.3 Lawn coverage
The product has GPS Assisted Navigation that
helps the product select the most optimal
operation.
In more complex gardens operation can be
improved by carrying out some of the manual
settings in the Lawn coverage menu.
3.16.3.1 To disable and enable the GPS function
Disable the GPS Assisted Navigation to make
manual settings in
Lawn Coverage
.
Note:
It is recommended to use GPS Assisted
Navigation.
1.
Select
GPS assisted navigation
.
2.
Tap the On/Off to enable or disable
GPS
assisted navigation
.
Note:
When GPS assisted navigation is
enabled it is used as long as there is a GPS
service. The GPS assisted navigation is
used even if manual settings have been
made. Only when GPS service is not
available, the manual settings are used.
3.16.3.2 Area 1-5 > Enable/disable
Each area can be enabled/disabled, without
having to reenter the settings.
1.
Tap the
On/Off
bar for Area 1-5.
3.16.3.3 Area 1-5 > How? and How far?
Specify to the right, left or Guide depending on
which direction the product should go. The
direction (left or right) is when facing the charging
station.
1.
Slide the horizontal bar to alternate between
Lawn coverage
settings.
2.
Slide the horizontal bar to change the
distance.
The default settings let the product follow the
guide wire 300 m / 328 yd. in 20% of the times it
leaves the charging station. If the guide wire in
reality is less than 300 m / 328 yd. the product
will follow it to the point where the guide wire is
connected to the boundary wire.
3.16.3.4 Area 1-5 > How often?
How often the product should go to the remote
area is selected as a proportion of the total
number of times it leaves the charging station. At
all other times, the products starts to mow close
to the charging station.
Select the percentage that corresponds to the
size of the remote area relative to the total work
area. If the remote area is for instance half of the
total work area, 50% should be selected. A lower
figure should be specified if the remote area is
smaller. If more areas are used, take into account
that the total figure cannot exceed 100%.
1.
Slide the horizontal bar to change the
percentage.
3.16.4 Corridor width
3.16.4.1 To set the corridor width of the boundary
wire
The boundary wire corridor is the area adjacent
to the boundary wire, which the product uses to
1102 - 002 -
Installation -
25