Home » Husqvarna Manuals » Lawn Mowers » Husqvarna AUTOMOWER 550H » Manual Viewer

Husqvarna AUTOMOWER 550H Owner Manual - Page 42

Weak GPS signal, ble the GPS function

View all Husqvarna AUTOMOWER 550H manuals

Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Message Guide 1 not found Guide 2 not found Guide 3 not found Cause The guide wire is not connected to the charging station. Break in the guide wire. Action Check that the guide wire's connector is tightly connected to the charging station. Refer to To install the guide wire on page 20. Find out where the break is. Replace the damaged section of the guide wire with a new loop wire and splice using an original coupler. The guide wire is not connected to the boundary loop. Check that the guide wire is connected correctly to the boundary loop. Refer to To install the guide wire on page 20. Guide calibration failed The product has failed to calibrate the guide wire. Check that the guide wires are installed according to the instructions. Refer to To install the guide wire on page 20. Guide calibration The product has succeeded to calibrate No action required. accomplished the guide wire. GPS navigation problem Problem with the GPS assisted naviga- Contact your local Husqvarna repre- tion equipment. sentative if this message appears often. Weak GPS signal The GPS signal is weak for the current work area. GPS assisted navigation cannot be used. If the message appears often, disable the GPS assisted navigation and instead use the manual settings for Lawn coverage. Refer to To disable and enable the GPS function on page 25. Difficult finding home The product has been following the The installation has not been done cor- boundary wire several laps without find- rectly. Refer to Installation on page 15. ing the charging station. Wrong corridor width setting on boundary wire. Refer to To set the corridor width of the boundary wire on page 25. The product was started on a Secondary area with the Main area setting. Temporary prob- Please try again. lem with the server. Contact your local Husqvarna representative if this message appears often. Connection problems Problem with the Automower® Connect module Restart the product. If there still is a connection problem, try to unpair the product (My mowers) and then pair it again. If the problem remains, contact your local Husqvarna representative. Connection settings restored Settings for wireless connectivity have Check and revise settings if necessary. been restored due to an error. 42 - Troubleshooting 1102 - 002 -

Section	Page
Contents	2
Introduction	3
Support	3
Product description	3
Automower® Connect	3
Product overview	4
Symbols on the product	5
Symbols in Automower® Connect	6
Symbols on the battery	6
Overview of the settings structure (1)	7
Overview of the settings structure (2)	8
Overview of the settings structure (3) (Bluetooth® short-range connectivity only)	9
Safety	10
Safety definitions	10
General safety instructions	10
IMPORTANT. READ CAREFULLY BEFORE USE. KEEP FOR FUTURE REFERENCE	11
Safety instructions for operation	12
Use	12
Battery safety	13
How to lift and move the product	13
Maintenance	14
In the event of a thunderstorm	14
Installation	15
Introduction - Installation	15
Before the installation of the wires	15
Before the installation of the product	15
To examine where to put the charging station	15
To examine where to put the power supply	16
To examine where to put the boundary wire	16
To put the boundary wire in a slope	17
Passages	17
To make an island	17
To make a secondary area	17
To examine where to put the guide wire	18
Work area examples	18
Installation of the product	19
To install the charging station	19
To install the boundary wire	19
To install the guide wire	20
To put the wire into position with stakes	20
To bury the boundary wire or the guide wire	20
To change the position of the boundary wire or the guide wire	20
To extend the boundary wire or the guide wire	21
After the installation of the product	21
To do a visual check of the charging station	21
To start the product for the first time	21
Automower® Connect	21
To install Automower® Connect	22
To pair Automower® Connect and the product	22
Automower® Connect menu	22
Dashboard	22
Map	22
Map settings	22
Settings in Automower® Connect	22
Timer settings	22
To calculate the timer setting	23
Edit timer settings	23
Edit current timer settings	23
Add a new timer setting	23
Cutting height	23
To set the cutting height	23
Operation	23
Weather timer	23
ECO mode	24
Spiral cutting	24
Installation	24
Methods for the product to find the charging station	24
Finding the charging station	25
Lawn coverage	25
To disable and enable the GPS function	25
Area 1-5 > Enable/disable	25
Area 1-5 > How? and How far?	25
Area 1-5 > How often?	25
Corridor width	25
To set the corridor width of the boundary wire	25
To set the corridor width of the guide wire	26
Exit angles	26
Exit angles > Sectors	26
To set the reversing distance	26
To set the Drive Past Wire function	26
Accessories	26
Mower house	26
Ultrasonic	27
General (Bluetooth® only)	27
Time & Date	27
To reset to factory settings	27
Security (Bluetooth® only)	27
To create a new loop signal	27
Change PIN code	27
Theft protection	27
Alarm duration	27
Lifted	27
Turned upside down	27
STOP button pressed	27
Time lock	28
GeoFence	28
Automower® Connect (Bluetooth® only)	28
Messages (Bluetooth® only)	28
My mowers	28
Automower® Direct	28
To start to use Automower® Direct	29
Husqvarna Fleet Services™	29
To connect to the product with Husqvarna Fleet Services™	29
Operation	30
Main switch	30
Start	30
Operating mode - Start	30
Main area	30
Override timer	30
Secondary area	31
Operating mode - Park	31
Park until further notice	31
Start on next timer	31
Parking duration	31
The charging station's park button	31
Operating mode - Pause	31
Stop	31
Switch off	31
Charge a flat battery	32
Maintenance	33
Introduction - maintenance	33
Clean the product	33
Chassis and blade disc	33
Chassis	33
Wheels	33
Cover	33
Charging station	33
Replace the blades	34
To replace the blades	34
Battery	34
Winter service	35
Troubleshooting	36
Introduction - troubleshooting	36
Fault messages	36
Information messages	41
LED indicator lamp on the charging station	43
LED indicator lamp on the product	44
Symptoms	45
Finding breaks in the loop wire	46
Transportation, storage and disposal	49
Transportation	49
Storage	49
Disposal	49
To remove the battery	49
Technical data	50
Technical data	50
Registered trademarks	52
Warranty	53
Guarantee terms	53
Applicable to US/CA market	54
Supplier's Declaration of Conformity	54

Match case Limit results 1 per page

Message

Cause

Action

Guide 1 not found

Guide 2 not found

Guide 3 not found

The guide wire is not connected to the

charging station.

Check that the guide wire’s connector

is tightly connected to the charging sta-

tion. Refer to

To install the guide wire

on page 20

Break in the guide wire.

Find out where the break is. Replace

the damaged section of the guide wire

with a new loop wire and splice using

an original coupler.

The guide wire is not connected to the

boundary loop.

Check that the guide wire is connected

correctly to the boundary loop. Refer to

To install the guide wire on page 20

Guide calibration

failed

The product has failed to calibrate the

guide wire.

Check that the guide wires are installed

according to the instructions. Refer to

To install the guide wire on page 20

Guide calibration

accomplished

The product has succeeded to calibrate

the guide wire.

No action required.

GPS navigation

problem

Problem with the GPS assisted naviga-

tion equipment.

Contact your local Husqvarna repre-

sentative if this message appears of-

ten.

Weak GPS signal

The GPS signal is weak for the current

work area. GPS assisted navigation

cannot be used.

If the message appears often, disable

the GPS assisted navigation and in-

stead use the manual settings for Lawn

coverage. Refer to

To disable and ena-

ble the GPS function on page 25

Difficult finding

home

The product has been following the

boundary wire several laps without find-

ing the charging station.

The installation has not been done cor-

rectly. Refer to

Installation on page 15

Wrong corridor width setting on boun-

dary wire. Refer to

To set the corridor

width of the boundary wire on page 25

The product was started on a Secon-

dary area with the Main area setting.

Temporary prob-

lem with the serv-

er.

Please try again.

Contact your local Husqvarna repre-

sentative if this message appears of-

ten.

Connection prob-

lems

Problem with the Automower

Connect

module

Restart the product. If there still is a

connection problem, try to unpair the

product

(My mowers)

and then pair it

again. If the problem remains, contact

your local Husqvarna representative.

Connection set-

tings restored

Settings for wireless connectivity have

been restored due to an error.

Check and revise settings if necessary.

- Troubleshooting

1102 - 002 -