Husqvarna AUTOMOWER 550H Owner Manual - Page 27

Ultrasonic, General (Bluetooth® only), Time & Date, To reset to factory settings

Get Husqvarna AUTOMOWER 550H PDF manuals and user guides View all Husqvarna AUTOMOWER 550H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

3.17.2 Ultrasonic Ultrasonic is applicable for Automower® 550H. It ensures that the product reduces speed before it hits an obstacle. This function can be disabled, which means the product will always operate at a lower speed. 3.18 General (Bluetooth® only) This function is used to set time and date, or to reset to default settings. 3.18.1 Time & Date This function allows you to set current time and date manually, or to choose to get it from the mobile device. • Set time: Tap Edit, then enter the correct time and tap OK. • Set date: Tap Edit, then enter the correct time and tap OK. 3.18.2 To reset to factory settings This function allows you to reset the product to the factory default settings. The following settings are however not altered: • Security level • PIN code • Loop signal • Messages • Date & Time 1. Select Reset to factory settings. 2. Confirm by choosing Reset. 3.19 Security (Bluetooth® only) In the settings menu settings relating to security and the connection between the product and the charging station can be made. 3.19.1 To create a new loop signal The loop signal is randomly selected to create a unique link between the product and the charging station. In rare cases, there may be a need to generate a new signal, for instance if two adjacent installations have a very similar signal. 1. Place the product in the charging station. 2. Select Create new loop signal. 3. Await confirmation that the loop signal has been generated. This normally takes about 10 seconds. 3.19.2 Change PIN code Note: Changing the PIN code is not possible if the LED indicator lamp on top of the product is either red (error) or green (mowing). 1. Enter the current PIN code. 2. Enter the new PIN code. 3. Confirm by entering the same code again. Make a note of the new PIN code on the designated line in Memo. Refer to Introduction on page 3. 3.19.3 Theft protection In the Theft protection menu it is possible to set the alarm duration and also what events should trigger the alarm. 3.19.3.1 Alarm duration There is a possibility to set how long the alarm signal should last. A setting between 1 and 10 minutes is possible. 3.19.3.2 Lifted If the alarm Lifted is enabled, the product senses changes in the lift sensors, and the alarm goes off. 3.19.3.3 Turned upside down If the alarm Turned upside down is enabled, the product senses changes in the tilt sensors, and the alarm goes off. 3.19.3.4 STOP button pressed If the alarm "STOP button pressed" is enabled, the alarm goes off if someone presses the STOP button. To avoid alarm, the operator must be within short-range (Bluetooth®). Note: After an alarm has been triggered, you must be close by the product, and clear the alarm in the app by entering the PIN code (only available for short-range Bluetooth® connectivity). 1102 - 002 - Installation - 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
3.17.2 Ultrasonic
Ultrasonic is applicable for Automower
®
550H. It
ensures that the product reduces speed before it
hits an obstacle. This function can be disabled,
which means the product will always operate at a
lower speed.
3.18 General (Bluetooth
®
only)
This function is used to set time and
date, or to reset to default settings.
3.18.1 Time & Date
This function allows you to set current time and
date manually, or to choose to get it from the
mobile device.
•
Set time:
Tap
Edit
, then enter the correct
time and tap
OK
.
•
Set date:
Tap
Edit
, then enter the correct
time and tap
OK
.
3.18.2 To reset to factory settings
This function allows you to reset the product to
the factory default settings.
The following settings are however not altered:
•
Security level
•
PIN code
•
Loop signal
•
Messages
•
Date & Time
1.
Select
Reset to factory settings
.
2.
Confirm by choosing
Reset
.
3.19 Security (Bluetooth
®
only)
In the settings menu settings relating
to security and the connection between
the product and the charging station
can be made.
3.19.1 To create a new loop signal
The loop signal is randomly selected to create a
unique link between the product and the charging
station. In rare cases, there may be a need to
generate a new signal, for instance if two
adjacent installations have a very similar signal.
1.
Place the product in the charging station.
2.
Select
Create new loop signal
.
3.
Await confirmation that the loop signal has
been generated. This normally takes about
10 seconds.
3.19.2 Change PIN code
Note:
Changing the PIN code is not possible if
the LED indicator lamp on top of the product is
either red (error) or green (mowing).
1.
Enter the current PIN code.
2.
Enter the new PIN code.
3.
Confirm by entering the same code again.
Make a note of the new PIN code on the
designated line in Memo. Refer to
Introduction on
page 3
.
3.19.3 Theft protection
In the
Theft protection
menu it is possible to set
the alarm duration and also what events should
trigger the alarm.
3.19.3.1 Alarm duration
There is a possibility to set how long the alarm
signal should last. A setting between 1 and 10
minutes is possible.
3.19.3.2 Lifted
If the alarm
Lifted
is enabled, the product senses
changes in the lift sensors, and the alarm goes
off.
3.19.3.3 Turned upside down
If the alarm
Turned upside down
is enabled, the
product senses changes in the tilt sensors, and
the alarm goes off.
3.19.3.4 STOP button pressed
If the alarm
"STOP button pressed"
is enabled,
the alarm goes off if someone presses the
STOP
button. To avoid alarm, the operator must be
within short-range (Bluetooth
®
).
Note:
After an alarm has been triggered, you
must be close by the product, and clear the alarm
in the app by entering the PIN code (only
available for short-range Bluetooth
®
connectivity).
1102 - 002 -
Installation -
27