Husqvarna RZ5424 Kawasaki Owners Manual - Page 34

Moving Machine By Hand, Use extreme caution when loading

Get Husqvarna RZ5424 Kawasaki PDF manuals and user guides View all Husqvarna RZ5424 Kawasaki manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

OPERATION Moving Machine By Hand When pushing or pulling the mower, engage the IZT (Integrated Zeroturn Transaxle) bypass linkages. The release levers are located on each side of the rear of the unit below the rear engine plate. 1. Raise the deck to the highest (transport) position. 2. Pull the release levers up and out of the keyhole slots. Release the levers with the head outside the bracket and held into the bypass setting. 3. To reengage the IZTs to drive, reverse the above procedure. Load the machine into truck or trailer by driving up ramps in low gear. DO NOT LIFT! The machine is not intended to be lifted by hand. WARNING! Use extreme caution when loading the machine into a truck or trailer using ramps. There is the possibility of serious injury or death if the machine falls off the ramps. 2 1 1. IZT locked into the bypass position 2. Linkage lever, engaged Right side, IZT linkage WARNING! Make no adjustments without: • the engine stopped, • the ignition key removed, • the parking brake activated WARNING! Bypass linkages are located close to the muffler. To prevent burns, the engine should be shut off and allowed to cool before the bypass linkage levers are handled. 8058-059 34

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
1
2
OPERATION
34
Moving Machine By Hand
When pushing or pulling the mower, engage the IZT
(Integrated Zeroturn Transaxle) bypass linkages. The
release levers are located on each side of the rear of
the unit below the rear engine plate.
1.
Raise the deck to the highest (transport) position.
2.
Pull the release levers up and out of the keyhole
slots. Release the levers with the head outside the
bracket and held into the bypass setting.
3.
To reengage the IZTs to drive, reverse the above
procedure.
Load the machine into truck or trailer by driving up
ramps in low gear. DO NOT LIFT! The machine is not
intended to be lifted by hand.
8058-059
1. IZT locked into the bypass position
2. Linkage lever, engaged
Right side, IZT linkage
WARNING!
Make no adjustments without:
•
the engine stopped,
•
the ignition key removed,
•
the parking brake activated
WARNING!
Use extreme caution when loading the
machine into a truck or trailer using
ramps. There is the possibility of
serious injury or death if the machine
falls off the ramps.
WARNING!
Bypass linkages are located close
to the muffler. To prevent burns, the
engine should be shut off and allowed
to cool before the bypass linkage
levers are handled.