Husqvarna T525 Owner Manual - Page 19

To do a check of the start/stop switch

Get Husqvarna T525 PDF manuals and user guides View all Husqvarna T525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

To do a check of the throttle trigger and the throttle trigger lockout 1. Make sure that the throttle trigger and throttle trigger lockout move freely and that the return spring works correctly. 2. Make sure that the chain catcher is stable and attached to the body of the product. 2. Push down the throttle trigger lockout and make sure that it goes back to its initial position when you release it. To do a check of the vibration damping system 1. Make sure that there are no cracks or deformation on the vibration damping units. 2. Make sure that the vibration damping units are correctly attached to the engine unit and handle unit. Refer to Product overview on page 2 for information about where the vibration damping system is on your product. To do a check of the start/stop switch 1. Start the engine. 2. Push the start/stop switch to the STOP position. The engine must stop. 3. Make sure that the throttle trigger is locked at the idle position when the throttle trigger lockout is released. To do a check of the muffler 1. Loosen the screw to the muffler guard. 4. Start the chainsaw and apply full throttle. 5. Release the throttle trigger and make sure that the saw chain stops and stays stationary. WARNING: If the saw chain rotates when the throttle trigger is in the idle position, speak to your servicing dealer. To do a check of the chain catcher 1. Make sure that there is no damage on the chain catcher. 732 - 017 - 11.10.2019 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
To do a check of the throttle trigger and the
throttle trigger lockout
1.
Make sure that the throttle trigger and throttle trigger
lockout move freely and that the return spring works
correctly.
2.
Push down the throttle trigger lockout and make sure
that it goes back to its initial position when you
release it.
3.
Make sure that the throttle trigger is locked at the
idle position when the throttle trigger lockout is
released.
4.
Start the chainsaw and apply full throttle.
5.
Release the throttle trigger and make sure that the
saw chain stops and stays stationary.
WARNING:
If the saw chain rotates
when the throttle trigger is in the idle
position, speak to your servicing dealer.
To do a check of the chain catcher
1.
Make sure that there is no damage on the chain
catcher.
2.
Make sure that the chain catcher is stable and
attached to the body of the product.
To do a check of the vibration damping
system
1.
Make sure that there are no cracks or deformation
on the vibration damping units.
2.
Make sure that the vibration damping units are
correctly attached to the engine unit and handle unit.
Refer to
Product overview on page 2
for information
about where the vibration damping system is on your
product.
To do a check of the start/stop switch
1.
Start the engine.
2.
Push the start/stop switch to the STOP position. The
engine must stop.
To do a check of the muffler
1.
Loosen the screw to the muffler guard.
732 - 017 - 11.10.2019
19