Husqvarna V548 - 2023 Owner Manual - Page 12

To engage and disengage the parking brake, To disengage and engage the drive system

Get Husqvarna V548 - 2023 PDF manuals and user guides View all Husqvarna V548 - 2023 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

To engage and disengage the parking brake • Pull the parking brake lever rearward to engage the parking brake. Refer to Product overview on page 3 for the location of the parking brake. Note: The product must be stationary when you engage the parking brake. • Push the parking brake forward to disengage the parking brake. To disengage and engage the drive system CAUTION: Only disengage the drive system when the product is parked on level ground. If it is necessary to move the product by hand, with the engine off, the drive system must be disengaged. • Pull out the drive system lever fully to disengage the drive system. The drive system lever is on the left side of the product. • Push the transport latch lever (B) forward to lower the cutting deck into mow position. To set the cutting height 1. Set the cutting deck in transport position. Refer to To set the cutting deck in transport position or mow position on page 12. 2. Push in the button on the top of the pin and pull the pin out. 3. Put the pin in the hole for the correct cutting height. 4. Push the transport latch lever forward to lower the cutting deck into mow position. To start the engine 1. Push the PTO button to disengage the drive on the cutting deck. • Push in the drive system lever fully to engage the drive system. To set the cutting deck in transport position or mow position The cutting deck must be in transport position during transportation. • Pull back the deck lifting lever (A) fully. The transport latch lever (B) locks the deck lifting lever in transport position. 2. Move the throttle lever to ½ throttle position. 3. Engage the parking brake. Refer to To disengage and engage the drive system on page 12. 4. If the engine is cold, pull up the choke control fully. A B 12 1994 - 002 - 05.12.2022

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
To engage and disengage the
parking brake
•
Pull the parking brake lever rearward to engage
the parking brake. Refer to
Product overview on
page 3
for the location of the parking brake.
Note:
The product must be stationary when
you engage the parking brake.
•
Push the parking brake forward to disengage the
parking brake.
To disengage and engage the drive
system
CAUTION:
Only disengage the
drive system when the product is parked
on level ground.
If it is necessary to move the product by hand, with
the engine off, the drive system must be disengaged.
•
Pull out the drive system lever fully to disengage
the drive system. The drive system lever is on
the left side of the product.
•
Push in the drive system lever fully to engage the
drive system.
To set the cutting deck in transport
position or mow position
The cutting deck must be in transport position during
transportation.
•
Pull back the deck lifting lever (A) fully. The
transport latch lever (B) locks the deck lifting
lever in transport position.
A
B
•
Push the transport latch lever (B) forward to
lower the cutting deck into mow position.
To set the cutting height
1.
Set the cutting deck in transport position. Refer
to
To set the cutting deck in transport position or
mow position on page 12
.
2.
Push in the button on the top of the pin and pull
the pin out.
3.
Put the pin in the hole for the correct cutting
height.
4.
Push the transport latch lever forward to lower
the cutting deck into mow position.
To start the engine
1.
Push the PTO button to disengage the drive on
the cutting deck.
2.
Move the throttle lever to ½ throttle position.
3.
Engage the parking brake. Refer to
To
disengage and engage the drive system on page
12
.
4.
If the engine is cold, pull up the choke control
fully.
12
1994 - 002 - 05.12.2022