Home » Husqvarna Manuals » Lawn Mowers » Husqvarna V548 - 2023 » Manual Viewer

Husqvarna V548 - 2023 Owner Manual - Page 18

To do a check of the parking brake, To charge the battery, To do an emergency start of the engine

View all Husqvarna V548 - 2023 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

2. Pull the handle to open the engine cover fully. battery to or near the negative terminal of the weak battery. 3. Tilt the engine cover slightly up and lift the rear edge up to remove the engine cover. 4. Install in the opposite sequence. To do a check of the parking brake 1. Park the product on a slope with a hard surface. Note: Do not park the product on a grass slope when you do a check of the parking brake. 2. Engage the parking brake. 3. If the product starts to move with the parking brake engaged, let an approved service agent adjust the parking brake. 4. Disengage the parking brake. To charge the battery • Charge the battery if it is too weak to start the engine. Refer to Battery charging times on page 30 for battery charging times. • Use a standard battery charger. CAUTION: Do not use a boost charger or start booster. A boost charger or a start booster will cause damage to the electrical system of the product. • Always disconnect the battery charger before you start the engine. To do an emergency start of the engine If the battery is too weak to start the engine, you can use jumper cables to do an emergency start. This product has a 12 V system with negative ground. The product that is used for the emergency start must also have a 12 V system with negative ground. To connect the jumper cables WARNING: Risk of explosion because of explosive gas that comes from the battery. Do not connect the negative terminal of the fully charged CAUTION: Do not use the battery of the product to start other vehicles. 1. Connect one end of the red cable to the POSITIVE battery terminal (+) on the weak battery (A). C B D A 2. Connect the other end of the red cable to the POSITIVE battery terminal (+) on the fully charged battery (B). WARNING: Do not short circuit the ends of the red cable against the chassis. 3. Connect one end of the black cable to the NEGATIVE battery terminal (-) on the fully charged battery (C). 4. Connect the other end of the black cable to a CHASSIS GROUND (D), away from the fuel tank and the battery. To remove the jumper cables Note: Remove the jumper cables in the opposite sequence to how you connect them. 1. Remove the BLACK cable from the chassis. 2. Remove the BLACK cable from the fully charged battery. 3. Remove the RED cable from the 2 batteries. To remove and install the battery 1. Pull open the engine cover to get access to the battery. 18 1994 - 002 - 05.12.2022

Section	Page
Contents	2
Conformity certificates	2
USA requirements	2
Introduction	2
Pre-delivery inspection and product numbers	2
Product description	3
Intended use	3
Support / Help	3
Product overview	3
Stand on or walk behind position	4
Steering controls	4
Operator Presence Control (OPC)	4
Ignition key	4
Throttle control	4
Choke control	4
PTO (Power Take-Off) button	4
Fuel gauge	5
Fuel shut-off valve	5
Fuses	5
Hour meter	5
Symbols on the product	5
Product liability	6
Safety	6
Safety definitions	6
General safety instructions	6
Safety instructions regarding children	7
Safety instructions for operation	7
Safety instructions for operation on slopes	7
Safety instructions for operation on slopes	8
Personal protective equipment	8
Safety devices on the product	8
To do a check of the ignition lock	8
Operation conditions	8
Parking brake	8
Muffler	9
To do a check of the muffler	9
Spark arrestor	9
Protective covers	9
Fuel safety	9
Transport safety	9
Hauling	9
Battery safety	9
Safety instructions for maintenance	10
Operation	10
Introduction	10
To operate the product for the first time	10
To do before you operate the product	11
To fill fuel	11
To set the product in stand on or walk behind position	11
To adjust the adjustable bar	11
To engage and disengage the parking brake	12
To disengage and engage the drive system	12
To set the cutting deck in transport position or mow position	12
To set the cutting height	12
To start the engine	12
To operate the product	13
To stop the engine	14
To adjust the tracking speed	14
To get a good cutting result	14
To do a 3-point turn	14
Maintenance	15
Introduction	15
Maintenance schedule	15
Maintenance schedule for the operator	15
To clean the product	17
To clean the engine and the muffler	17
To clean the battery	17
To remove the covers	17
To remove and install the engine cover	17
To do a check of the parking brake	18
To charge the battery	18
To do an emergency start of the engine	18
To connect the jumper cables	18
To remove the jumper cables	18
To remove and install the battery	18
Tire pressure	19
To remove and install the front wheels	19
To adjust the anti-scalp rollers	19
To adjust the parallelism of the cutting deck	19
To adjust the neutral position	20
To adjust the neutral switches	20
To examine the blades	21
To replace the blades	21
To remove the deck drive belt	21
To install the deck drive belt	21
To remove the deck belt	21
To install the deck belt	22
To remove the pump belt	22
To install the pump belt	22
To do a check of the engine oil level	22
To replace the engine oil	23
To do a check of the hydraulic oil level	23
Lubrication, general information	24
Lubrication schedule	24
To lubricate the front wheels	25
To lubricate the cutting deck spindles	25
Troubleshooting	25
Troubleshooting schedule	25
Transportation, storage and disposal	27
Transportation	27
Storage	27
Disposal	28
Technical data	29
Technical data	29
Battery charging times	30
Service	31
Service	31
Contenido	32
Certificados de conformidad	32
Requisitos para EE. UU.	32
Introducción	32
Inspección previa a la entrega y números de producto	32
Descripción del producto	33
Uso previsto	33
Soporte/ayuda	33
Descripción general del producto	34
Posición de caminar o permanecer de pie en la parte trasera	34
Controles de la dirección	35
Control de presencia del operador (OPC)	35
Llave de encendido	35
Control del acelerador	35
Estrangulador	35
Botón de toma de fuerza (PTO)	35
Indicador de combustible	36
Válvula de corte de combustible	36
Fusibles	36
Medidor de horas	36
Símbolos en el producto	36
Responsabilidad del fabricante	37
Seguridad	37
Definiciones de seguridad	37
Instrucciones generales de seguridad	37
Instrucciones de seguridad relacionadas con los niños	38
Instrucciones de seguridad para el funcionamiento	38
Instrucciones de seguridad para el uso en pendientes	38
Instrucciones de seguridad para el uso en pendientes	39
Equipo de protección personal	39
Dispositivos de seguridad en el producto	39
Para comprobar el bloqueo del encendido	40
Condiciones de funcionamiento	40
Freno de estacionamiento	40
Silenciador	40
Para revisar el silenciador	40
Apagachispas	40
Cubiertas protectoras	40
Seguridad de combustible	40
Seguridad del transporte	41
Transporte	41
Seguridad de la batería	41
Instrucciones de seguridad para el mantenimiento	41
Funcionamiento	42
Introducción	42
Para usar el producto por primera vez	42
Haga lo siguiente antes de usar el producto	42
Para agregar combustible	42
Para colocar el producto en posición de caminar o permanecer de pie en la parte trasera	43
Para ajustar la barra ajustable	43
Para acoplar y desacoplar el freno de estacionamiento	43
Para desacoplar y acoplar el sistema de transmisión	43
Para colocar el equipo de corte en la posición de transporte o posición de corte	44
Ajuste de la altura de corte	44
Para arrancar el motor	44
Para hacer funcionar el producto	45
Para detener el motor	46
Para ajustar la velocidad de desplazamiento	46
Para conseguir un buen resultado de corte	46
Para hacer un giro de 3 puntos	47
Mantenimiento	47
Introducción	47
Programa de mantenimiento	47
Programa de mantenimiento para el usuario	47
Para limpiar el producto	49
Para limpiar el motor y el silenciador	50
Para limpiar la batería	50
Para quitar las cubiertas	50
Para retirar e instalar la cubierta del motor	50
Para comprobar el freno de estacionamiento	50
Para cargar la batería	50
Para hacer una parada de emergencia del motor	50
Para conectar los cables de puente	50
Para retirar los cables de puente	51
Para retirar e instalar la batería	51
Presión de los neumáticos	51
Para retirar e instalar las ruedas delanteras	51
Para ajustar las ruedas de apoyo	51
Para ajustar el paralelismo del equipo de corte	52
Para ajustar la posición neutra	52
Para ajustar los interruptores de neutro	53
Para examinar las cuchillas	54
Para sustituir las hojas	54
Para retirar la correa de transmisión del equipo	54
Para instalar la correa de transmisión del equipo	54
Para extraer la correa del equipo	54
Para instalar la correa del equipo	55
Para extraer la correa de la bomba	55
Para instalar la correa de la bomba	55
Para revisar el nivel de aceite del motor	55
Para cambiar el aceite del motor:	56
Para revisar el nivel de aceite hidráulico	56
Lubricación; información general	57
Programa de lubricación	57
Para lubricar las ruedas delanteras	58
Para lubricar los ejes del equipo de corte	58
Solución de problemas	58
Programa de solución de problemas	58
Transporte, almacenamiento y eliminación de residuos	61
Transporte	61
Almacenamiento	61
Eliminación	61
Datos técnicos	62
Datos técnicos	62
Tiempos de carga de la batería	63
Servicio	64

Match case Limit results 1 per page

Pull the handle to open the engine cover fully.

Tilt the engine cover slightly up and lift the rear

edge up to remove the engine cover.

Install in the opposite sequence.

To do a check of the parking brake

Park the product on a slope with a hard surface.

Note:

Do not park the product on a grass

slope when you do a check of the parking brake.

Engage the parking brake.

If the product starts to move with the parking

brake engaged, let an approved service agent

adjust the parking brake.

Disengage the parking brake.

To charge the battery

•

Charge the battery if it is too weak to start the

engine. Refer to

Battery charging times on page

for battery charging times.

•

Use a standard battery charger.

CAUTION:

Do not use a boost

charger or start booster. A boost

charger or a start booster will cause

damage to the electrical system of

the product.

•

Always disconnect the battery charger before

you start the engine.

To do an emergency start of the

engine

If the battery is too weak to start the engine, you can

use jumper cables to do an emergency start. This

product has a 12 V system with negative ground.

The product that is used for the emergency start

must also have a 12 V system with negative ground.

To connect the jumper cables

WARNING:

Risk of explosion

because of explosive gas that comes

from the battery. Do not connect the

negative terminal of the fully charged

battery to or near the negative terminal

of the weak battery.

CAUTION:

Do not use the battery of

the product to start other vehicles.

Connect one end of the red cable to the

POSITIVE battery terminal (+) on the weak

battery (A).

Connect the other end of the red cable to

the POSITIVE battery terminal (+) on the fully

charged battery (B).

WARNING:

Do not short circuit

the ends of the red cable against the

chassis.

Connect one end of the black cable to the

NEGATIVE battery terminal (-) on the fully

charged battery (C).

Connect the other end of the black cable to a

CHASSIS GROUND (D), away from the fuel tank

and the battery.

To remove the jumper cables

Note:

Remove the jumper cables in the opposite

sequence to how you connect them.

Remove the BLACK cable from the chassis.

Remove the BLACK cable from the fully charged

battery.

Remove the RED cable from the 2 batteries.

To remove and install the battery

Pull open the engine cover to get access to the

battery.

1994 - 002 - 05.12.2022