IBM 6400-I10 Operation Guide - Page 96

Fault Correction Procedure

Get IBM 6400-I10 PDF manuals and user guides View all IBM 6400-I10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

status and fault messages Fault Correction Procedure 1 Press any key on the operator panel, except Stop, to silence the alarm if necessary. Pressing the Form Feed key will silence the alarm and cause the paper to move. The top-of-form setting will be lost. 2 Write down the number of the displayed error message. 3 Use the fault explanation to fix the problem, if possible. 4 Press Stop to clear the fault message. Press Start to return to READY state, and resume printing. 5 If the fault message reappears, power off the printer, wait 15 seconds, then power on the printer. 6 Run your print job again. If the fault message reappears, turn off power to the printer, then call an IBM service representative. Otherwise, no further attention is required. The following pages list each printer status message and fault message. For fault messages, suggestions are offered for correcting the fault condition. 82 Operator's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
status and fault messages
82
Operator’
s Guide
Fault Correction Procedure
1
Press any key on the operator panel,
except
Stop
, to silence the alarm if
necessary. Pressing the
Form Feed
key
will silence the alarm and cause the
paper to move. The top-of-form setting
will be lost.
2
Write down the number of the displayed
error message.
3
Use the fault explanation to fix the
problem, if possible.
4
Press
Stop
to clear the fault message.
Press
Start
to return to READY state,
and resume printing.
5
If the fault message reappears, power
of
f the printer
, wait 15 seconds, then
power on the printer.
6
Run your print job again. If the fault
message reappears, turn off power to
the printer
, then call an IBM service
representative. Otherwise, no further
attention is required.
The following pages list each printer status
message and fault message. For fault messages,
suggestions are offered for correcting the fault
condition.