IBM 8835 Installation Guide - Page 30

Attention, Press down on the retention clip at the front of the power-cord module

Get IBM 8835 - Eserver 325 - 1 GB RAM PDF manuals and user guides
UPC - 000435158314
View all IBM 8835 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

5. On the rear panel, squeeze the expansion-slot clip to unlock the clip; then, pull the clip out from the server until it stops and rotate the clip as shown in the following illustration. It remains loosely attached to the server. Adapter retention bracket Alignment tab Expansionslot clip (adapter slot 1) Power-cord module Expansionslot clip (adapter slot 2) Retention clip Attention: Avoid touching the components and gold-edge connectors on the adapter. Ensure that the adapter is completely and correctly seated in the slot. Incomplete insertion might cause damage to the system board or to the adapter. 6. Remove the expansion slot cover from the slot. 7. To gain access to PCI-X slot 1, remove the PCI riser card from its connector. Riser card System board 8. To gain access to PCI-X slot 2, remove the power-cord module. a. Press down on the retention clip at the front of the power-cord module and slide the module toward the front of the server until the alignment tab is free of the slot on the side of the server. b. Lift and place the power-cord module out of the server as far as the power supply cable permits. 16 IBM 325 Type 8835: Option Installation Guide Eserver

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
5.
On the rear panel, squeeze the expansion-slot clip to unlock the clip; then, pull
the clip out from the server until it stops and rotate the clip as shown in the
following illustration. It remains loosely attached to the server.
Power-cord
module
Adapter
retention
bracket
Expansion-
slot clip (adapter slot 1)
Expansion-
slot clip (adapter slot 2)
Retention clip
Alignment tab
Attention:
Avoid touching the components and gold-edge connectors on the
adapter. Ensure that the adapter is completely and correctly seated in the slot.
Incomplete insertion might cause damage to the system board or to the
adapter.
6.
Remove the expansion slot cover from the slot.
7.
To gain access to PCI-X slot 1, remove the PCI riser card from its connector.
System board
Riser card
8.
To gain access to PCI-X slot 2, remove the power-cord module.
a.
Press down on the retention clip at the front of the power-cord module and
slide the module toward the front of the server until the alignment tab is
free of the slot on the side of the server.
b.
Lift and place the power-cord module out of the server as far as the power
supply cable permits.
16
IBM
Eserver
325 Type 8835: Option Installation Guide