IBM 8835 Installation Guide - Page 43

Replacing a fan assembly, User's Guide, Documentation, Hardware Maintenance

Get IBM 8835 - Eserver 325 - 1 GB RAM PDF manuals and user guides
UPC - 000435158314
View all IBM 8835 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

7. Reinstall the server cover, and connect the cables. 8. Turn on the server. 9. Start the Configuration/Setup Utility program and set configuration parameters. v Set the system date and time. v Set the user (power-on) password. v Reconfigure the server. For details, see the section about using the Configuration/Setup Utility program in the User's Guide on the IBM Documentation CD. Eserver Replacing a fan assembly The server comes with five replaceable fans. Complete the following steps to replace the fan assembly. Use this procedure to replace any fan in the server. 1. Review the safety information beginning on page v, and "Installation guidelines" on page 9. 2. Turn off the server and all attached peripheral devices. Disconnect all power cords; then, disconnect all external signal cables from the server. 3. Remove the server from the rack; then, remove the server cover (see "Removing the cover and bezel" on page 11). Attention: When you handle static-sensitive devices, take precautions to avoid damage from static electricity. For information about handling these devices, see "Handling static-sensitive devices" on page 9. 4. Determine which fan to replace by checking the LED at each fan; a lit LED indicates the fan to replace. Note: For more information about the LEDs, see the Hardware Maintenance Manual and Troubleshooting Guide on the IBM Documentation Eserver CD. Chapter 2. Installing options 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
7.
Reinstall the server cover, and connect the cables.
8.
Turn on the server.
9.
Start the Configuration/Setup Utility program and set configuration parameters.
v
Set the system date and time.
v
Set the user (power-on) password.
v
Reconfigure the server.
For details, see the section about using the Configuration/Setup Utility program
in the
User’s Guide
on the IBM
Eserver
Documentation
CD.
Replacing a fan assembly
The server comes with five replaceable fans.
Complete the following steps to replace the fan assembly. Use this procedure to
replace any fan in the server.
1.
Review the safety information beginning on page v, and “Installation guidelines”
on page 9.
2.
Turn off the server and all attached peripheral devices. Disconnect all power
cords; then, disconnect all external signal cables from the server.
3.
Remove the server from the rack; then, remove the server cover (see
“Removing the cover and bezel” on page 11).
Attention:
When you handle static-sensitive devices, take precautions to
avoid damage from static electricity. For information about handling these
devices, see “Handling static-sensitive devices” on page 9.
4.
Determine which fan to replace by checking the LED at each fan; a lit LED
indicates the fan to replace.
Note:
For more information about the LEDs, see the
Hardware Maintenance
Manual and Troubleshooting Guide
on the IBM
Eserver
Documentation
CD.
Chapter 2. Installing options
29