IBM HS21 User Guide - Page 39

technician.

Get IBM HS21 - BladeCenter - 8853 PDF manuals and user guides
UPC - 000435947550
View all IBM HS21 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

12. Touch the static-protective package that contains the new microprocessor to any unpainted metal surface on the blade server or any unpainted metal surface on any other grounded rack component in the rack you are installing the microprocessor in for at least 2 seconds; then, remove the microprocessor from the package. 13. Remove the cover from the bottom of the microprocessor. Microprocessor Alignment marks Microprossor retainer Microprocessor socket Attention: Do not press the microprocessor into the socket. 14. Center the microprocessor over the microprocessor socket. Align the triangle on the corner of the microprocessor with the triangle on the corner of the socket and carefully place the microprocessor into the socket. Attention: Make sure that the microprocessor is oriented and aligned correctly in the socket before you try to close the microprocessor retainer. 15. Carefully close the microprocessor retainer. 16. Rotate the locking lever on the microprocessor socket to the closed and locked position. Make sure that the lever is secured in the locked position by the tab on the microprocessor socket. Attention: v Do not set down the heat sink after you remove the plastic cover. v Do not touch the thermal grease on the bottom of the heat sink. Touching the thermal grease will contaminate it. If the thermal grease on the microprocessor or heat sink becomes contaminated, contact your service technician. Heat sink Thermal material 17. Remove the plastic protective cover from the bottom of the heat sink. 18. Make sure that the thermal material is still on the bottom of the heat sink; then, align and place the heat sink on top of the microprocessor in the retention bracket, thermal material side down. Press firmly on the heat sink. 19. Align the two screws on the heat sink with the holes on the heat-sink retention module. Chapter 3. Installing options 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
12.
Touch
the
static-protective
package
that
contains
the
new
microprocessor
to
any
unpainted
metal
surface
on
the
blade
server
or
any
unpainted
metal
surface
on
any
other
grounded
rack
component
in
the
rack
you
are
installing
the
microprocessor
in
for
at
least
2
seconds;
then,
remove
the
microprocessor
from
the
package.
13.
Remove
the
cover
from
the
bottom
of
the
microprocessor.
Microprocessor
Microprocessor
socket
Alignment marks
Microprossor retainer
Attention:
Do
not
press
the
microprocessor
into
the
socket.
14.
Center
the
microprocessor
over
the
microprocessor
socket.
Align
the
triangle
on
the
corner
of
the
microprocessor
with
the
triangle
on
the
corner
of
the
socket
and
carefully
place
the
microprocessor
into
the
socket.
Attention:
Make
sure
that
the
microprocessor
is
oriented
and
aligned
correctly
in
the
socket
before
you
try
to
close
the
microprocessor
retainer.
15.
Carefully
close
the
microprocessor
retainer.
16.
Rotate
the
locking
lever
on
the
microprocessor
socket
to
the
closed
and
locked
position.
Make
sure
that
the
lever
is
secured
in
the
locked
position
by
the
tab
on
the
microprocessor
socket.
Attention:
v
Do
not
set
down
the
heat
sink
after
you
remove
the
plastic
cover.
v
Do
not
touch
the
thermal
grease
on
the
bottom
of
the
heat
sink.
Touching
the
thermal
grease
will
contaminate
it.
If
the
thermal
grease
on
the
microprocessor
or
heat
sink
becomes
contaminated,
contact
your
service
technician.
Heat sink
Thermal material
17.
Remove
the
plastic
protective
cover
from
the
bottom
of
the
heat
sink.
18.
Make
sure
that
the
thermal
material
is
still
on
the
bottom
of
the
heat
sink;
then,
align
and
place
the
heat
sink
on
top
of
the
microprocessor
in
the
retention
bracket,
thermal
material
side
down.
Press
firmly
on
the
heat
sink.
19.
Align
the
two
screws
on
the
heat
sink
with
the
holes
on
the
heat-sink
retention
module.
Chapter
3.
Installing
options
27