IBM HS21 User Guide - Page 40

Installing, Concurrent, Feature - driver

Get IBM HS21 - BladeCenter - 8853 PDF manuals and user guides
UPC - 000435947550
View all IBM HS21 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

20. Press firmly on the captive screws and tighten them with a screwdriver, alternating between screws until they are tight. If possible, rotate each two full rotations at a time. Repeat until the screws are tight. Do not overtighten the screws by using excessive force. If you are using a torque wrench, tighten the screws to 8.5 to 13 Newton-meters (Nm) (6.3 to 9.6 inch-pounds). If you have other options to install or remove, do so now; otherwise, go to "Completing the installation" on page 34. Installing a Concurrent KVM Feature Card The following illustration shows how to install a cKVM Feature Card. cKVM feature card To install a cKVM Feature Card, complete the following steps: 1. Read the safety information that begins on page v and "Installation guidelines" on page 15. 2. If the blade server is installed in a BladeCenter unit, remove it (see "Removing the blade server from the BladeCenter unit" on page 17 for instructions). 3. Carefully lay the blade server on a flat, static-protective surface. 4. Open the blade server cover (see "Opening the blade server cover" on page 18 for instructions). 5. If a Memory and I/O Expansion Blade is installed, remove it (see "Removing an expansion unit" on page 19). 6. If a small-form-factor expansion card or a high-speed expansion card is installed, remove it. 7. Touch the static-protective package that contains the cKVM Feature Card to any unpainted metal surface on the BladeCenter unit or any unpainted metal surface on any other grounded rack component; then, remove the card from the package. 8. Locate the cKVM connector and orient the cKVM Feature Card. 9. Slide the right side of the card (the side of the card that is away from the cKVM connector) between the two tabs at the right side of the expansion card bracket; then, gently pivot the card into the connector. Note: For device-driver and configuration information needed to complete the installation of the cKVM Feature Card, see the documentation that comes with the card. 28 BladeCenter HS21 Type 8853: Installation and User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
20.
Press
firmly
on
the
captive
screws
and
tighten
them
with
a
screwdriver,
alternating
between
screws
until
they
are
tight.
If
possible,
rotate
each
two
full
rotations
at
a
time.
Repeat
until
the
screws
are
tight.
Do
not
overtighten
the
screws
by
using
excessive
force.
If
you
are
using
a
torque
wrench,
tighten
the
screws
to
8.5
to
13
Newton-meters
(Nm)
(6.3
to
9.6
inch-pounds).
If
you
have
other
options
to
install
or
remove,
do
so
now;
otherwise,
go
to
“Completing
the
installation”
on
page
34.
Installing
a
Concurrent
KVM
Feature
Card
The
following
illustration
shows
how
to
install
a
cKVM
Feature
Card.
cKVM feature card
To
install
a
cKVM
Feature
Card,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
15.
2.
If
the
blade
server
is
installed
in
a
BladeCenter
unit,
remove
it
(see
“Removing
the
blade
server
from
the
BladeCenter
unit”
on
page
17
for
instructions).
3.
Carefully
lay
the
blade
server
on
a
flat,
static-protective
surface.
4.
Open
the
blade
server
cover
(see
“Opening
the
blade
server
cover”
on
page
18
for
instructions).
5.
If
a
Memory
and
I/O
Expansion
Blade
is
installed,
remove
it
(see
“Removing
an
expansion
unit”
on
page
19).
6.
If
a
small-form-factor
expansion
card
or
a
high-speed
expansion
card
is
installed,
remove
it.
7.
Touch
the
static-protective
package
that
contains
the
cKVM
Feature
Card
to
any
unpainted
metal
surface
on
the
BladeCenter
unit
or
any
unpainted
metal
surface
on
any
other
grounded
rack
component;
then,
remove
the
card
from
the
package.
8.
Locate
the
cKVM
connector
and
orient
the
cKVM
Feature
Card.
9.
Slide
the
right
side
of
the
card
(the
side
of
the
card
that
is
away
from
the
cKVM
connector)
between
the
two
tabs
at
the
right
side
of
the
expansion
card
bracket;
then,
gently
pivot
the
card
into
the
connector.
Note:
For
device-driver
and
configuration
information
needed
to
complete
the
installation
of
the
cKVM
Feature
Card,
see
the
documentation
that
comes
with
the
card.
28
BladeCenter
HS21
Type
8853:
Installation
and
User’s
Guide