IBM HS21 User Guide - Page 47

Installing, blade, server, bezel, assembly, Closing, cover

Get IBM HS21 - BladeCenter - 8853 PDF manuals and user guides
UPC - 000435947550
View all IBM HS21 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Installing the blade server bezel assembly The following illustration shows how to install the bezel assembly. Bezel-assembly release (both sides) Control-panel cable Bezel Control-panel connector To install the blade server bezel assembly, complete the following steps: 1. Read the safety information that begins on page v and "Installation guidelines" on page 15. 2. Connect the control-panel cable to the control-panel connector on the system board. 3. Carefully slide the bezel assembly onto the blade server until it clicks into place. Closing the blade server cover Attention: You cannot insert the blade server into the BladeCenter unit until the cover is installed and closed or an expansion unit is installed. Do not attempt to override this protection. The following illustration shows how to close the blade server cover. Blade-cover release Blade-cover release To close the blade server cover, complete the following steps: 1. Read the safety information that begins on page v and "Installation guidelines" on page 15. 2. If you removed the blade bezel assembly, replace it now (see "Installing the blade server bezel assembly" for instructions). 3. If the blade server system board is equipped with power connector J164 and a Memory and I/O Expansion Blade is not installed on the blade server, make sure that the power jumper is correctly installed in power connector J164. Chapter 3. Installing options 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Installing
the
blade
server
bezel
assembly
The
following
illustration
shows
how
to
install
the
bezel
assembly.
Control-panel
connector
Control-panel
cable
Bezel
Bezel-assembly
release (both sides)
To
install
the
blade
server
bezel
assembly,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
15.
2.
Connect
the
control-panel
cable
to
the
control-panel
connector
on
the
system
board.
3.
Carefully
slide
the
bezel
assembly
onto
the
blade
server
until
it
clicks
into
place.
Closing
the
blade
server
cover
Attention:
You
cannot
insert
the
blade
server
into
the
BladeCenter
unit
until
the
cover
is
installed
and
closed
or
an
expansion
unit
is
installed.
Do
not
attempt
to
override
this
protection.
The
following
illustration
shows
how
to
close
the
blade
server
cover.
Blade-cover
release
Blade-cover
release
To
close
the
blade
server
cover,
complete
the
following
steps:
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
15.
2.
If
you
removed
the
blade
bezel
assembly,
replace
it
now
(see
“Installing
the
blade
server
bezel
assembly”
for
instructions).
3.
If
the
blade
server
system
board
is
equipped
with
power
connector
J164
and
a
Memory
and
I/O
Expansion
Blade
is
not
installed
on
the
blade
server,
make
sure
that
the
power
jumper
is
correctly
installed
in
power
connector
J164.
Chapter
3.
Installing
options
35