Icom IC-R6 Instruction Manual - Page 42

Full/band/programmed link/programmed scan

Get Icom IC-R6 PDF manuals and user guides View all Icom IC-R6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

6 SCAN OPERATION ■ Full/band/programmed link/programmed scan q Push [V/M] to select the VFO mode. • Push [BAND] to select a desired frequency band. w Set the squelch level. e H old down [SCAN](MODE) for 1 second to enter the scan type selection mode. r Rotate [DIAL] to select a desired scanning type. • Select "ALL" for full scan, "BAND" for band scan, "P-LINK x" for programmed link scan (x= 0 to 9), "PROGxx" for programmed scan (xx= 0 to 24; only programmed scan edge numbers are displayed). t To start the scan, push [SCAN](MODE). • The scan pauses when a signal is received. • Rotate [DIAL] to change the scanning direction. This also resumes scanning. • Push [SCAN](MODE) again to stop the scan. During full/band scan During programmed/ link program scan [DIAL] • Full scan Hold down for 1 sec. Rotate • Program link scan Selectable between "0" to "9" if programmed (p. 53) • Band scan • Program scan NOTE: Instead of doing steps e to t, while holding down [SCAN](MODE), rotate [DIAL] to select a desired scan type. In this case, the scan starts after releasing [SCAN](MODE). ✔ CONVENIENT! The memorised skip frequencies can be skipped or scanned during a VFO scan. ➥ In the VFO mode, hold down [FUNC], then push [ ](V/M) to set the skip scan setting ON or OFF. (default: ON) Selectable between "0" to "24" if programmed (p. 30) The scan link name or scan name can be displayed instead of "P-LINK x" for program link scan (x= 0 to 9), "PROGxx" for programmed scan (xx= 0 to 24) when scan link name or scan name is programmed. Scan link name or scan name is not displayed during scan. 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
29
6
SCAN OPERATION
q
Push
[V/M]
to select the VFO mode.
• Push
[BAND]
to
select a desired frequency band.
w
Set the squelch level.
e
Hold down
[SCAN]
(MODE) for 1 second to enter the scan
type selection mode.
r
Rotate
[DIAL]
to select a desired scanning type.
• Select “ALL” for full scan, “BAND” for band scan, “P-LINK x” for
programmed link scan (x= 0 to 9), “PROGxx” for programmed
scan (xx= 0 to 24; only programmed scan edge numbers are
displayed).
[DIAL]
Selectable between
“0” to “24” if programmed (p. 30)
Selectable between
“0” to “9” if programmed (p. 53)
• Full scan
• Band scan
• Program link scan
• Program scan
Rotate
Hold down
for 1 sec.
t
To start the scan, push
[SCAN]
(MODE).
• The scan pauses when a signal is received.
• Rotate
[DIAL]
to change the scanning direction. This also
resumes scanning.
• Push
[SCAN]
(MODE) again to stop the scan.
During full/band scan
During programmed/
link program scan
NOTE:
Instead of doing steps
e
to
t
, while holding
down
[SCAN]
(MODE), rotate
[DIAL]
to select a desired
scan type. In this case, the scan starts after releasing
[SCAN]
(MODE).
✔
CONVENIENT!
The memorised skip frequencies can be skipped or scanned
during a VFO scan.
➥
In the VFO mode, hold down
[FUNC]
, then push
[
]
(V/M)
to
set the skip scan setting ON or OFF.
(default: ON)
■
Full/band/programmed link/programmed scan
The scan link name or scan name can be displayed
instead of “P-LINK x” for program link scan (x= 0 to 9),
“PROGxx” for programmed scan (xx= 0 to 24) when scan
link name or scan name is programmed.
Scan link name or scan name is not displayed during scan.