Icom IC-R6 Instruction Manual - Page 45

Programming other contents

Get Icom IC-R6 PDF manuals and user guides View all Icom IC-R6 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

SCAN OPERATION 6 ■ Programming other contents The programmed scan can store the scanning step, receive mode and attenuator settings. q Push [V/M] to select the memory mode. w Rotate [DIAL] to select a desired scan edge channel. e H old down [S.MW](V/M) for 1 second to enter the select memory write mode. • 1 short and 1 long beep sounds. • The " " icon and memory channel number blink. r W hile holding down [MODE], rotate [DIAL] to select the "TS," "MODE" or "ATT" item when programming the tuning step, the receive mode or the attenuator setting. • The item can also be selected by repeatedly pushing [MODE]. Scan step selection After released. Receive mode selection After released. Attenuator setting After released. 1 t R otate [DIAL] to select a desired option. 2 Or, select the d��i�s��p�l�a�y���w���h���e��n����e���r�a���s�i�n�g��t��h��e����c��o���n���t�e��n��ts� 3 from the option. • If is��s��e�l�e�c��t�e���d����i�n����t��h��i�s s��t�e���p th�e���p�r�o�g��r��a���m s���c��a���n����u���s��e��s��t�h�e� 4 VFO settings. yHold down [S.MW](V/M) for 1 second to program the 5 name and exit the programming mode. 6 • 3 beeps sound. 7 During the full/band scan: 8 The selected tuning step, received mode and attenuator set- tings in each frequency band are used. 9 During the programmed/programmed link scan: 10 The programmed tuning step, received mode and attenuator 11 settings in each programmed scan edge are used. 12 13 14 15 16 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
32
6
SCAN OPERATION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
■
Programming other contents
The programmed scan can store the scanning step, receive
mode and attenuator settings.
q
Push
[V/M]
to select the memory mode.
w
Rotate
[DIAL]
to select a desired scan edge channel.
e
Hold down
[S.MW]
(V/M) for 1 second to enter the select
memory write mode.
• 1 short and 1 long beep sounds.
• The “
” icon and memory channel number blink.
r
While holding down
[MODE]
, rotate
[DIAL]
to select the
“TS,” “MODE” or “ATT” item when programming the tuning
step, the receive mode or the attenuator setting.
• The item can also be selected by repeatedly pushing
[MODE]
.
Scan step selection
After
released.
Receive mode selection
After
released.
Attenuator setting
After
released.
t
Rotate
[DIAL]
to select a desired option.
Or, select the “-- -- -- --” display when erasing the contents
“-- -- -- --” display when erasing the contents
-- -- -- --” display when erasing the contents
” display when erasing the contents
display when erasing the contents
from the option.
• If “-- -- -- --” is selected in this step, the program scan uses the
“-- -- -- --” is selected in this step, the program scan uses the
-- -- -- --” is selected in this step, the program scan uses the
” is selected in this step, the program scan uses the
is selected in this step, the program scan uses the
VFO settings.
y
Hold down
[S.MW]
(V/M) for 1 second to program the
name and exit the programming mode.
• 3 beeps sound.
During the full/band scan:
The selected tuning step, received mode and attenuator set-
tings in each frequency band are used.
During the programmed/programmed link scan:
The programmed tuning step, received mode and attenuator
settings in each programmed scan edge are used.