Icom IP740D Instruction Manual

Icom IP740D Manual

Get Icom IP740D PDF manuals and user guides View all Icom IP740D manuals
Add to My Manuals
Save this manual to your list of manuals

Icom IP740D manual content summary:

  • Icom IP740D | Instruction Manual - Page 1
    INSTRUCTION MANUAL HYBRID IP TRANSCEIVER IP730D IP740D INTRODUCTION 1 ACCESSORIES 2 BEFORE USING 3 USING THE CELLULAR MODE 4 USING THE IDAS MODE 5 OTHER FUNCTIONS 6 SET MODE 7 FOR YOUR REFERENCE
  • Icom IP740D | Instruction Manual - Page 2
    you with years of trouble-free operation. IMPORTANT FIRST, CAREFULLY READ INSTRUCTIONS that is boxed with the transceiver. SAVE THIS INSTRUCTION MANUAL- This instruction manual contains additional important operating instructions for the transceiver. Icom, Icom Inc. and Icom logo are registered
  • Icom IP740D | Instruction Manual - Page 3
    Section 1 ACCESSORIES Supplied accessories 1-2 Attachable accessories 1-2 DDAntenna 1-2 DDBattery pack/Battery case 1-3 DDBelt clip 1-3 1-1
  • Icom IP740D | Instruction Manual - Page 4
    : ••DO NOT carry the transceiver by holding only the antenna. ••DO NOT connect an antenna other than the supplied antenna, or those listed in this manual. ••DO NOT transmit without an antenna. 1-2
  • Icom IP740D | Instruction Manual - Page 5
    1 ACCESSORIES Attachable accessories (Continued) DDBattery pack/Battery case CAUTION: ••DO NOT attach or detach the battery pack or the battery case when the transceiver is wet or soiled. This may result in water or dust getting into the transceiver, battery pack, or battery case and may damage them
  • Icom IP740D | Instruction Manual - Page 6
    Section 2 BEFORE USING Panel description 2-2 DDFront, top and side panels 2-2 DDStatus indicator 2-2 DDMulti-connector 2-2 DDAbout the assignable key functions 2-2 Function display 2-3 DDCellular mode 2-3 DDIDAS mode 2-3 DDCellular/IDAS mode 2-3 Basic operation 2-4 DDTurning ON the
  • Icom IP740D | Instruction Manual - Page 7
    2 BEFORE USING Panel description DDFront, top and side panels Antenna Connector [Emer] Rotary Selector [PTT] Speaker [Sub PTT] [Side 1] [Side 2] [Address] [Call History] [VOL] Status indicator Multiconnector Microphone Function display [FUNC] [CLR/Lock] [▲]/[▼] DDMulti-connector Connects to
  • Icom IP740D | Instruction Manual - Page 8
    by 3 bars. LLThe connected network type (4G or 3G) is displayed on the left top. ••Blinks when the transceiver location is out of the service area, or cannot receive a control signal. ••Displayed if the transceiver has not been authenticated. LLThe connected network type (4G or 3G) is displayed on
  • Icom IP740D | Instruction Manual - Page 9
    for the first time, the battery pack must be fully charged for optimum life and operation. See the BATTERY CHARGING section on the boxed INSTRUCTIONS. zzRotate [VOL] clockwise to the 12 o'clock position to turn ON the transceiver. LLThe dial is made tight for dust and water resistance. LLTo
  • Icom IP740D | Instruction Manual - Page 10
    Section 3 USING THE CELLULAR MODE Basic operation 3-2 DDOperating keys 3-2 DDReceiving and Transmitting 3-3 Advanced operation 3-4 DDAbout the Talkgroup Call 3-4 DDSelecting a Talkgroup number 3-5 DDSending a message (Message Call 3-6 DDBrowsing received messages 3-7 DDStatus Call 3-7
  • Icom IP740D | Instruction Manual - Page 11
    3 USING THE CELLULAR MODE Basic operation DDOperating keys Rotary Selector [Emer] [PTT] [VOL] [Sub PTT] [Side 1] [Side 2] [Address] [Call History] [FUNC] [CLR/Lock] [▲]/[▼] Rotary Selector [Emer] [PTT] [Sub PTT] [Side 1] [Side 2] [Address] [Call History] CLR/Lock] [FUNC] [VOL] Rotate to
  • Icom IP740D | Instruction Manual - Page 12
    3 USING THE CELLULAR MODE Basic operation (Continued) DDSelecting a call-to party 1. Push [Address] to display the Address book. LLThe Address book is displayed. 2. Push [Address] several times to toggle the call type. LLThe selectable call type may differ, depending on a presetting. 3. Rotate
  • Icom IP740D | Instruction Manual - Page 13
    3 USING THE CELLULAR MODE Advanced operation DDAbout the Talkgroup Call The Talkgroup Call function enables the user to communicate with call-to parties in the same Talkgroup. For example, in the illustration below, when the IP730D "00105" in its normal group "10002" selects Talkgroup "20001," it
  • Icom IP740D | Instruction Manual - Page 14
    3 USING THE CELLULAR MODE Advanced operation (Continued) D Selecting a Talkgroup number You can select a Talkgroup number if the Talkgroup Call function is assigned to the [FUNC] key� Ask your dealer for details� 1� Push [FUNC] to display the Function� • The Function screen is displayed� 2� Push [
  • Icom IP740D | Instruction Manual - Page 15
    3 USING THE CELLULAR MODE Advanced operation (Continued) D Sending a message (Message Call) You can send a message, depending on a presetting� Ask your dealer for details� 1. Selecting a call-to party 1� Push [Address] to display the Address book� • The Address book is displayed� 2� Push [Address]
  • Icom IP740D | Instruction Manual - Page 16
    3 USING THE CELLULAR MODE Advanced operation (Continued) D Browsing received messages You can browse received messages, depending on a presetting� Ask your dealer for details� 1� Push [Call History] to display the Call history� • The Call history is displayed� 2� Push [Call History] to display "Rx
  • Icom IP740D | Instruction Manual - Page 17
    3 USING THE CELLULAR MODE Advanced operation (Continued) DDToggling the SIM card The transceiver has two SIM card slots, SIM 1 and SIM 2. You can toggle which SIM card to use in the Detailed Set mode. 1. Turn OFF the transceiver, if it is turned ON. 2. While holding down [Address] and [FUNC],
  • Icom IP740D | Instruction Manual - Page 18
    Section 4 USING THE IDAS MODE Basic operation 4-2 DDOperating keys 4-2 DDSelecting a Zone 4-3 DDSelecting a channel 4-3 DDReceiving and transmitting 4-3 DDTransmitting Notes 4-3 Other functions 4-4 DDRadio Access Number (RAN 4-4 DDEncryption function 4-4 4-1
  • Icom IP740D | Instruction Manual - Page 19
    4 USING THE IDAS MODE Basic operation DDOperating keys Rotary Selector [Emer] [PTT] [VOL] [Sub PTT] [Side 1] [Side 2] [Address] [Call History] [FUNC] [CLR/Lock] [▲]/[▼] Rotary Selector [Emer] [PTT] [Sub PTT] [Side 1] [Side 2] [Address] [Call History] CLR/Lock] [FUNC] [VOL] Rotate to select
  • Icom IP740D | Instruction Manual - Page 20
    4 USING THE IDAS MODE Basic operation (Continued) DDSelecting a Zone Certain channels are grouped together and assigned to a Zone according to their intended use. For example, Analog channels 'Station 1' and 'Station 2' are assigned to an "Analog" Zone, and Digital channels 'Station 3' and 'Station
  • Icom IP740D | Instruction Manual - Page 21
    4 USING THE IDAS MODE Other functions DDRadio Access Number (RAN) Radio Access Number (RAN) is a signaling system designed for digital radio communications. When a channel is set up with a RAN, the squelch will open only when a call containing a matching RAN* is received. If a call containing a
  • Icom IP740D | Instruction Manual - Page 22
    Section 5 OTHER FUNCTIONS DDAbout the VS-3 Bluetooth headset 5-2 DDPairing with a Bluetooth device 5-3 DDSettings for the Bluetooth function 5-3 DDDisconnecting a paired device 5-4 DDInitializing the Pairing lists 5-4 Using the Emergency call function 5-5 DDThe Man Down function 5-6 DDThe
  • Icom IP740D | Instruction Manual - Page 23
    as using the transceiver's [PTT] switch. ••The [FWD], [RWD], and [PLAY] keys on the VS-3 are disabled while using the headset with the IP730D or IP740D. ••If the headset does not work correctly, even if the power is ON, push [RESET] with a pin to force power OFF. Microphone [PTT] [VOL] (+) [VOL
  • Icom IP740D | Instruction Manual - Page 24
    . LLPush [CLR/Lock] to cancel searching. ••If found, the device's name and BD address are displayed on the screen. (Example: ICOM BT-002) SET Bluetooth ON SET Search BT Device ICOM BT-002 2. Push [▲] or [▼] to select the headset to pair and connect, and then push [Call History]. ••"Connect" is
  • Icom IP740D | Instruction Manual - Page 25
    or device is correctly disconnected. LLDo the same steps to reconnect to the Bluetooth device. Pairing List ICOM BT-002 Unconnected DDInitializing the Pairing lists If you have problems with Bluetooth operation, initialize the pairing lists, as shown below. Initializing the Pairing list of the
  • Icom IP740D | Instruction Manual - Page 26
    can receive or transmit Emergency Call if the function is enabled. Transmitting: The instruction is for when the function is enabled. Ask your dealer for details. as obstructions, weather condition, and so on. Icom is not responsible for the destruction or damage caused by using the Emergency
  • Icom IP740D | Instruction Manual - Page 27
    mode is canceled. NOTE: The Man down function may not properly work, depending on the surrounding environment such as obstructions, weather condition, and so on. Icom is not responsible for the destruction or damage caused by using the Man Down function. 5-6
  • Icom IP740D | Instruction Manual - Page 28
    mode is canceled. NOTE: The Lone Worker function may not properly work, depending on the surrounding environment such as obstructions, weather condition, and so on� Icom is not responsible for the destruction or damage caused by using the Lone Worker function� 5-7
  • Icom IP740D | Instruction Manual - Page 29
    The Stationary Detection function may not properly work, depending on the surrounding environment such as obstructions, weather condition, and so on� Icom is not responsible for the destruction or damage caused by using the Stationary Detection function� ON Timer Motion is detected. Reminder Timer
  • Icom IP740D | Instruction Manual - Page 30
    5 OTHER FUNCTIONS Using the Voice Recorder function The transceiver can record and playback up to 10 of the latestincoming calls, depending on a presetting� L Records up to 4 minutes per call� If a call is longer than 4 minutes, the older will be automatically deleted� L Therecordablecalltype
  • Icom IP740D | Instruction Manual - Page 31
    5 OTHER FUNCTIONS Using assignable keys Functions shown below may be assigned to the [Sub PTT], [Side 1], and [Side 2] keys, depending on a presetting. Hold down or push these keys to use assigned functions. You can also assign these functions in the Detailed Set mode (p. 6-5). Function
  • Icom IP740D | Instruction Manual - Page 32
    5 OTHER FUNCTIONS Using the Dual mode You can use the Cellular mode and IDAS mode at the same time. DDMain mode and Sub mode When the Dual mode is selected, the Main mode and Sub mode are displayed as shown to the right. Main mode Sub mode Switching the operating mode: zzHold down [FUNC] for 1
  • Icom IP740D | Instruction Manual - Page 33
    Section 6 SET MODE Using the Set mode 6-2 DDBasic Set mode 6-2 DDDetailed Set mode 6-2 DDUsing the Set mode 6-2 Set mode items 6-3 DDCommon 6-3 DDCellular 6-7 DDIDAS 6-9 6-1
  • Icom IP740D | Instruction Manual - Page 34
    6 SET MODE Using the Set mode You can use the Set mode to set infrequently changed values or function settings. The transceiver has 2 types of Set modes, as shown below. LLYou cannot transmit or receive while the transceiver is in the Set mode. DDBasic Set mode 1. Turn OFF the transceiver, if it
  • Icom IP740D | Instruction Manual - Page 35
    6 SET MODE Set mode items The shaded items are also displayed in the Basic Set mode. LLItems or default values may be differ, depending on the transceiverʼs version or presettings. Ask your dealer for details. DDCommon Item LOG CLEAR FIRM UP RX Notify Vol. Notify Vol. Key-Touch Beep Internal Mic
  • Icom IP740D | Instruction Manual - Page 36
    6 SET MODE Set mode items (Continued) The shaded items are also displayed in the Basic Set mode. LLItems or default values may be differ, depending on the transceiverʼs version or presettings. Ask your dealer for details. DDCommon Item Man Down*2 Lone Worker*2 Stationary Detection*2 Motion
  • Icom IP740D | Instruction Manual - Page 37
    6 SET MODE Set mode items (Continued) The shaded items are also displayed in the Basic Set mode. LLItems or default values may be differ, depending on the transceiverʼs version or presettings. Ask your dealer for details. DDCommon Item Side 1 Push Side 1 Hold Side 2 Push Side 2 Hold Backlight
  • Icom IP740D | Instruction Manual - Page 38
    6 SET MODE Set mode items (Continued) The shaded items are also displayed in the Basic Set mode. LLItems or default values may be differ, depending on the transceiverʼs version or presettings. Ask your dealer for details. DDCommon Item Description Option/range BT Echo Canceller*5 Selects
  • Icom IP740D | Instruction Manual - Page 39
    + Vibration Selects whether or not to enable the Out- OFF or ON of-Area Warning Beep. The beep also sounds when the transceiver reenters the service area. Selects whether or not to mute the Side OFF or ON Tone when the transceiver is out-of-area. Selects whether or not to
  • Icom IP740D | Instruction Manual - Page 40
    6 SET MODE Set mode items (Continued) The shaded items are also displayed in the Basic Set mode. LLItems or default values may be differ, depending on the transceiverʼs version or presettings. Ask your dealer for details. DDCellular Item Description Option/range Default Echo Canceller
  • Icom IP740D | Instruction Manual - Page 41
    6 SET MODE Set mode items (Continued) The shaded items are also displayed in the Basic Set mode. LLItems or default values may be differ, depending on the transceiverʼs version or presettings. Ask your dealer for details. DDIDAS Item SQL Level Description Selects whether or not to display the
  • Icom IP740D | Instruction Manual - Page 42
    7-7 DDUsing the LC-195 carrying case 7-8 DDUsing the HM-238MC tiepin type microphone with a [Sub PTT] switch 7-9 DDUsing the HM-245T dtmf speaker microphone 7-10 Troubleshooting 7-11 7-1
  • Icom IP740D | Instruction Manual - Page 43
    8, 28 W-CDMA Band 1, 5 QPSK, 16QAM, 64QAM 0.25 W -95 dBm maximum, -102 dBm typical DDIDAS ••Frequency range: ••Number of conventional channels: ••Type of emission: IP730D IP740D USA version EUR/EXP/AUS version 136 MHz ~ 174 MHz 350 MHz ~ 470 MHz, 400 MHz ~ 520 MHz 128 ch / 8 Zone 11K0F3E (15.0kHz
  • Icom IP740D | Instruction Manual - Page 44
    than 1GHz), 1.0 uW (More than 1GHz) IP730D 60 dB minimum 70 dB typical IP740D 60 dB minimum 64 dB typical 5 % maximum, 1 % typical 34 dB minimum, dBuVemf maximum (at 20 dB SINAD) -2.0 dBuVemf typical (at 20 dB SINAD) IP740D USA/EXP version 0.32 uV maximum (at 12 dB SINAD) 0.17 uV typical (
  • Icom IP740D | Instruction Manual - Page 45
    7 FOR YOUR REFERENCE Options DDBattery pack/Battery case ••BP-302/BP-303 battery pack Battery Voltage pack Capacity Approximate battery life* BP-302 7.2 V 1950 mAh (Minimum) 15 hours 2010 mAh (Typical) BP-303 7.2 V 3250 mAh (Minimum) 25 hours 3350 mAh (Typical) * In the Cellular mode, the
  • Icom IP740D | Instruction Manual - Page 46
    read the ‛Battery caution' and ‛Charging caution' on the INSTRUCTIONS that boxed with the transceiver. Status indicator Light color Status completed. Blinks orange Charging failed. It may have some and green problems. NOTE: ••The transceiver MUST be turned OFF while charging. Otherwise:
  • Icom IP740D | Instruction Manual - Page 47
    the ‛Battery caution' and ‛Charging caution' on the INSTRUCTIONS that boxed with the transceiver. Status indicator Light color chargers. Fuse replacement If a fuse blows, find and repair the cause of the problem. Then replace the damaged fuse with a new, adequately rated fuse. Fuse type: 5
  • Icom IP740D | Instruction Manual - Page 48
    7 FOR YOUR REFERENCE Options (Continued) DDUsing the BP-305 battery case Install 5 × AA (LR6) size alkaline batteries, as shown below. 1. Open the battery case. 4. Insert the battery holder to the battery case until the tab makes a 'click' sound. 2. Push the tab (1), and then remove the
  • Icom IP740D | Instruction Manual - Page 49
    7 FOR YOUR REFERENCE Options (Continued) DDUsing the LC-195 carrying case The LC-195 is a leather case that is usable when the battery pack is attached. Adjust the fixing position with the hook-and-loop fasteners. Hook-and-loop fastener Attach an optional MB-57L shoulder strap if necessary
  • Icom IP740D | Instruction Manual - Page 50
    7 FOR YOUR REFERENCE Options (Continued) DDUsing the HM-238MC tiepin type microphone with a [Sub PTT] switch The HM-238MC is a Tie-clip type microphone that can operate the [PTT], [Sub PTT], and [Side 1] switches of the transceiver. NOTE: When the HM-238MC is attached to the transceiver, no audio
  • Icom IP740D | Instruction Manual - Page 51
    7 FOR YOUR REFERENCE Options (Continued) DDUsing the HM-245T dtmf speaker microphone The HM-245T is the microphone that has Ten-keypad, that allows you to send DTMF codes. You can connect an earphone (user supplied) to the earphone jack. NOTE: When the HM-245T is attached to the transceiver, audio
  • Icom IP740D | Instruction Manual - Page 52
    7 FOR YOUR REFERENCE Troubleshooting The following conditions are not due to a malfunction. Connecting..." is displayed (standby screen is not displayed) ••The transceiver is located out of the service area. - Move your location. - Restart the transceiver. No reply is received. ••The transceiver is
  • Icom IP740D | Instruction Manual - Page 53
    7 FOR YOUR REFERENCE Troubleshooting (Continued) The charging indicator blinks orange, or alternately blinks orange and green ••The battery pack is not properly inserted. - Properly insert the battery pack. (p. 7-5) ••Charging
  • Icom IP740D | Instruction Manual - Page 54
    How the World Communicates A7605-3EX-4 © 2020-2022 Icom Inc. Jan. 2022 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
7
FOR YOUR REFERENCE
6
SET MODE
5
OTHER FUNCTIONS
4
USING THE IDAS MODE
3
USING THE CELLULAR MODE
2
BEFORE USING
1
ACCESSORIES
INTRODUCTION
INSTRUCTION MANUAL
HYBRID IP TRANSCEIVER
IP730D
IP740D