Home » Intel Manuals » Motherboards » Intel BB5000XALR » Manual Viewer

Intel BB5000XALR Specification Update - Page 26

Drives may not be detected or may go offline in the Intel® Server System

Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Enterprise Platforms and Services Marketing Monthly Specification Update 41. SuSE* Linux Enterprise Server unable to boot after basic installation Problem During SuSE* Linux Enterprise Server installation, if a USB floppy drive is used to load the mass storage driver, SuSE* Linux Enterprise Server might not boot after basic installation. The following message may display: resume device /dev/sdb1 not found (ignoring) waiting for device /dev/sdb2 to appear not found -- exiting to /bin/sh $ Implication During installation, the USB floppy device is recognized as sda, and the mass storage is recognized as sdb. After reboot, the mass storage is now recognized as sda, but SuSE* Linux Enterprise Server still tries to load system files from sdb. To resolve this issue, you must modify the grub menu list file and the fstab file. Status No Fix. Workaround http://www.intel.com/support/motherboards/server/sb/CS-025446.htm describes this issue and its workaround. 42. Drives may not be detected or may go offline in the Intel® Server System SR2500ALBRP when operating at SATA 3GB/s data rate Problem In the Intel® Server System SR2500ALBRP with a passive midplane, hard drives may not maintain stable operation at 3GB/s data rate. The problem is known to exist when using the on-board ESB2 controller with any 3GB/s capable drive. The active midplane is not affected. Implication The drives may not be detected during boot or may go offline during an operating system installation or stress load. Status The erratum is fixed with the new revision of the passive midplane FALPASMP MM# 901687, TA# D43781-003, PBA# E24192-203 that will improve SATA signal margins. Workaround Force hard drives to operate at 1.5GB/s data rate. The SATA data rate change does not have a significant impact on hard drive performance as the data rate of 1.5GB/s is still substantially higher than sustained drive media throughput. The active midplane is not affected. On most drives, the SATA data rate can be forced to 1.5GB/s by installing a jumper on the drive. If jumpering the HDD is not an option, contact your HDD supplier for alternate options. 20

Section	Page
Preface	7
Summary Tables of Changes	8
Errata	11
1. IPMI over serial direct connect not supported	11
2. Serial over LAN and IPMI over LAN connections may terminate unexpectedly under certain conditions	11
3. Intermittent beep code 1-5-2-1 when booting with two processors	11
4. Power supply population errors may not display in the SEL	11
5. Fan 5 may report a reading of 0 RPM after the BMC is updated	12
6. The BMC may not respond to the IPMI command, Send Message sent via LAN	12
7. Fans may take a long time to slow down after fan boosting	13
8. System requires ~35 seconds after AC power is applied before the power button responds	13
9. SEL events for Hot-swap Controller (HSC) may appear after a DC cycle	13
10. Fans may run faster than expected after exiting BIOS setup	13
11. System fault LED may report incorrect status for some events	14
12. Fan removal does not generate a SEL event	14
13. Power supply redundancy state is misleading when only one power supply is installed	15
14. Hot-swap Controller (HSC) and Local Control Panel (LCP) updates may take a long time	15
15. Console Redirection Baud Rate Setting auto changing to 19.2K with Serial Over LAN (SOL) active	15
16. Serial Over LAN (SOL) unable to redirect DOS output	16
17. Password on boot not supported	16
18. Intel® Embedded Server RAID Technology II option is not enabled in initial BIOS release	16
19. HSC and BMC versions intermittently not seen in BIOS setup	16
20. Intel® Server Boards S5000PAL/S5000XAL and Intel® Server System SR1500AL show a “Changes in Hardware or Drivers Detected” error message during WHQL ACPI stress testing	17
21. POST LEDs do not turn off after operating system loads	17
22. Checkup7.exe (microcode update utility) is not storing microcode in BIOS	18
23. Intel® RAID Controller SRCSAS144E causes systems to reset multiple times before completing POST	18
24. Change Logo Utility does not save modified BIOS capsule files with correct extension	19
25. PS/2 keyboards and mice may stop functioning after Red Hat* Enterprise Linux is installed	19
26. Failures seen installing to a SATA drive when SATA is set to “Legacy” in the BIOS setup	20
27. System hangs after disabling on-board video in the BIOS setup	20
28. The SMBIOS entry point may not be visible under certain hardware configurations	20
29. Intel® Embedded Server RAID Technology II and I/O module IRQ routing conflict	21
30. SuSE* Linux Enterprise Server may not install successfully with Intel® Embedded Server RAID Technology II enabled	21
31. Red Hat* Enterprise Linux 4 and BIOS setup display a different L2 cache size for the Quad-Core Intel® Xeon® processor 5300 Series	22
32. Change Logo Utility causes BIOS corruption	22
33. Microsoft Windows System Event Viewer* may record Error Event with ID 11	22
34. After the system reboots, the POST screen may generate \	23
35. Intel® RAID Web Console 2 utility displays “Unexpected Sensor” warning message in Microsoft Windows* operating system	23
36. Random drives may go offline when a sixth drive is installed and Intel® Embedded Server RAID Technology II is enabled in the Intel® Server System SR2500ALBRP	24
37. Intel recommends enterprise-class hard drives for use with Intel® Server Systems	24
38. Dual Gigabit Expansion Module may not properly reset	24
39. SAS drive in a ROMB RAID 5 may drop offline during a reboot in the Intel® Server System SR2500PALLX	25
40. Intel® Server System SR2500ALLX sixth hard drive filler panel is difficult to remove	25
41. SuSE* Linux Enterprise Server unable to boot after basic installation	26
42. Drives may not be detected or may go offline in the Intel® Server System SR2500ALBRP when operating at SATA 3GB/s data rate	26
43. New versions of BMC firmware with previous versions of BIOS cause system POST failure	27
44. Intel® Server System SR2500ALLX may operate louder than expected	27
45. Red Hat* Enterprise Linux may report the wrong processor speed	27
46. The SuSE* Linux Enterprise Server 10 driver for SAS HW RAID causes unwanted error logs during installation	27
47. IERR or thermal trip event reported in System Event Log (SEL) after system power on	28
48. USB device generates “The following boot-start or system-start driver(s) failed to load: i8042prt\	29
49. Microsoft Windows* and Intel® RAID Web Console II report an error when the ASR2500SATAPE kit is used	29
50. System may log IERRs when running certain Red Hat* Enterprise Linux versions on the Intel® Server Board S5000PAL with video driver ati_drv.o 6.5.6	29
51. Microsoft Windows* operating systems installed without a service pack will display blue screen with BIOS 79 and 81	30
52. Sluggish system performance may be experienced with BMC 60	31
53. Downgrading the firmware of the Integrated RAID (ROMB), Intel® Embedded Server RAID Technology II, or SAS may cause system damage	31
54. In the Intel® Server Systems SR2500ALLX and SR1550ALSAS, flashing of SAS firmware 1.22 and SAS BIOS 06.16.00 makes hard drive #1 (upper left drive tray) undetected during SAS controller scanning	31
55. Microsoft Windows 2003 R2 SP2* may display blue screen during an operating system boot or shutdown with a specific version of Intel( I/OAT driver	32
56. Server System Event Log (SEL) time may be one day later than BIOS time after entering year 2008.	33
57. Performance Power Management Error in Microsoft Windows Server 2008*	33
58. Midplane2 hardware RAID produces unexpected beep sounds during system POST	34
59. Platform Confidence Test (PCT) fails with BIOS 89/91 on Intel® Server Board S5000PAL/S5000XAL	34
60. USB mouse may hang in BIOS 94 RAID Console	34
61. PCI IBIST Error with BIOS 84	35
62. System May Hang during Login or Shutdown	35
63. Hard Disks Are Difficult to Install in Intel® Server System SR2500AL and Intel® Server Chassis SR2500	35
64. System May not Boot After Multiple DC power Cycles with BIOS Revision R0098	36
65. System will not skip CD/DVD drive with BIOS Revision R0098 when RMM2 installed	36
66. Please use AXXMINIDIMM512 as the replacement solution for AXXMINIDIMM which is EOLed	37
67. Minus “year” number to go past “2000” at BIOS “system date” set up interface will cause the server system to hang	37
68. Please do not downgrade BIOS from factory shipped BIOS 101 to any previous version	37
69. The Serial Port Console Redirection displays the Adaptec® 5805 RAID Configuration Utility incorrectly	38
Documentation Changes	39
1. The SMBUS block diagram (Figure #16) provided in Rev. 1.1 of the Intel® Server Board S5000PAL/S5000XAL TPS requires changes to accurately reflect production hardware design	39
2. The power block diagram (Figure #25) as provided in Rev. 1.1 of the Intel® Server Board S5000PAL/S5000XAL TPS does not reflect the final, production-level baseboard design	40
3. SAS/SAS RAID midplane board (Figure #22) as provided in Rev.1.0 of the Intel® Server System SR2500AL TPS should swap the descriptions of items A and K	41

Match case Limit results 1 per page

Enterprise Platforms and Services Marketing

Monthly Specification Update

41.

SuSE* Linux Enterprise Server unable to boot after basic installation

Problem

During SuSE* Linux Enterprise Server installation, if a USB floppy drive is used

to load the mass storage driver, SuSE* Linux Enterprise Server might not boot

after basic installation.

The following message may display:

resume device /dev/sdb1 not found (ignoring)

waiting for device /dev/sdb2 to

appear

..............................

not found -- exiting to

/bin/sh

Implication

During installation, the USB floppy device is recognized as sda, and the mass

storage is recognized as sdb. After reboot, the mass storage is now recognized

as sda, but SuSE* Linux Enterprise Server still tries to load system files from

sdb. To resolve this issue, you must modify the grub menu list file and the fstab

file.

Status

No Fix.

Workaround

http://www.intel.com/support/motherboards/server/sb/CS-025446.htm

describes this issue and its workaround.

42.

Drives may not be detected or may go offline in the Intel® Server System

SR2500ALBRP when operating at SATA 3GB/s data rate

Problem

In the Intel

Server System SR2500ALBRP with a passive midplane, hard

drives may not maintain stable operation at 3GB/s data rate. The problem is

known to exist when using the on-board ESB2 controller with any 3GB/s

capable drive. The active midplane is not affected.

Implication

The drives may not be detected during boot or may go offline during an

operating system installation or stress load.

Status

The erratum is fixed with the new revision of the passive midplane FALPASMP

MM# 901687, TA# D43781-003, PBA# E24192-203 that will improve SATA

signal margins.

Workaround

Force hard drives to operate at 1.5GB/s data rate. The SATA data rate change

does not have a significant impact on hard drive performance as the data rate

of 1.5GB/s is still substantially higher than sustained drive media throughput.

The active midplane is not affected.

On most drives, the SATA data rate can be forced to 1.5GB/s by installing a

jumper on the drive. If jumpering the HDD is not an option, contact your HDD

supplier for alternate options.