Intel BLKD945GCLF2D Product Specification - Page 18

IDE Support - processors

Get Intel BLKD945GCLF2D PDF manuals and user guides View all Intel BLKD945GCLF2D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Intel Desktop Board D945GCLF2 Technical Product Specification 1.6.2 USB The board supports up to eight USB 2.0 ports, supports UHCI and EHCI, and uses UHCI- and EHCI-compatible drivers. The ICH7 provides the USB controller for all ports. The port arrangement is as follows: • Four ports are implemented with dual stacked back panel connectors • Four ports are routed to two separate front panel USB headers NOTE Computer systems that have an unshielded cable attached to a USB port may not meet FCC Class B requirements, even if no device is attached to the cable. Use shielded cable that meets the requirements for full-speed devices. For information about The location of the USB connectors on the back panel The location of the front panel USB headers Refer to Figure 8, page 41 Figure 9, page 42 1.6.3 IDE Support The board provides three IDE interface connectors: • One parallel ATA IDE connector that supports two devices • Two serial ATA connectors that support one device per connector 1.6.3.1 Parallel ATE IDE Interface The ICH7's Parallel ATA IDE controller has one bus-mastering Parallel ATA IDE interface. The Parallel ATA IDE interface supports the following modes: • Programmed I/O (PIO): processor controls data transfer. • 8237-style DMA: DMA offloads the processor, supporting transfer rates of up to 16 MB/sec. • Ultra DMA: DMA protocol on IDE bus supporting host and target throttling and transfer rates of up to 33 MB/sec. • ATA-66: DMA protocol on IDE bus supporting host and target throttling and transfer rates of up to 66 MB/sec. ATA-66 protocol is similar to Ultra DMA and is device driver compatible. • ATA-100: DMA protocol on IDE bus allows host and target throttling. The ICH7's ATA-100 logic can achieve read transfer rates up to 100 MB/sec and write transfer rates up to 88 MB/sec. NOTE ATA-66 and ATA-100 are faster timings and require a specialized cable to reduce reflections, noise, and inductive coupling. The Parallel ATA IDE interface also supports ATAPI devices (such as CD-ROM drives) and ATA devices using the transfer modes. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
Intel Desktop Board D945GCLF2 Technical Product Specification
18
1.6.2
USB
The board supports up to eight USB 2.0 ports, supports UHCI and EHCI, and uses
UHCI- and EHCI-compatible drivers.
The ICH7 provides the USB controller for all ports.
The port arrangement is as
follows:
•
Four ports are implemented with dual stacked back panel connectors
•
Four ports are routed to two separate front panel USB headers
±
NOTE
Computer systems that have an unshielded cable attached to a USB port may not
meet FCC Class B requirements, even if no device is attached to the cable.
Use
shielded cable that meets the requirements for full-speed devices.
For information about
Refer to
The location of the USB connectors on the back panel
Figure 8, page 41
The location of the front panel USB headers
Figure 9, page 42
1.6.3
IDE Support
The board provides three IDE interface connectors:
•
One parallel ATA IDE connector that supports two devices
•
Two serial ATA connectors that support one device per connector
1.6.3.1
Parallel ATE IDE Interface
The ICH7’s Parallel ATA IDE controller has one bus-mastering Parallel ATA IDE
interface.
The Parallel ATA IDE interface supports the following modes:
•
Programmed I/O (PIO):
processor controls data transfer.
•
8237-style DMA:
DMA offloads the processor, supporting transfer rates of up to
16 MB/sec.
•
Ultra DMA:
DMA protocol on IDE bus supporting host and target throttling and
transfer rates of up to 33 MB/sec.
•
ATA-66:
DMA protocol on IDE bus supporting host and target throttling and
transfer rates of up to 66 MB/sec.
ATA-66 protocol is similar to Ultra DMA and is
device driver compatible.
•
ATA-100:
DMA protocol on IDE bus allows host and target throttling.
The ICH7’s
ATA-100 logic can achieve read transfer rates up to 100 MB/sec and write transfer
rates up to 88 MB/sec.
±
NOTE
ATA-66 and ATA-100 are faster timings and require a specialized cable to reduce
reflections, noise, and inductive coupling.
The Parallel ATA IDE interface also supports ATAPI devices (such as CD-ROM drives)
and ATA devices using the transfer modes.