Intel D525MW Product Guide - Page 40

Clearing Passwords, Table 13. Jumper Settings for the BIOS Setup Program Modes - bios update

Get Intel D525MW PDF manuals and user guides View all Intel D525MW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Intel Desktop Board D525MW Product Guide Figure 15 shows the location of the Desktop Board's BIOS configuration jumper block. Table 13. Jumper Settings for the BIOS Setup Program Modes Jumper Setting Mode Normal (default) (1-2) Description The BIOS uses the current configuration and passwords for booting. Configure (2-3) Recovery (None) After the Power-On Self-Test (POST) runs, the BIOS displays the Maintenance Menu. Use this menu to clear passwords. The BIOS recovers data from a recovery diskette in the event of a failed BIOS update. Clearing Passwords This procedure assumes that the board is installed in the computer and the configuration jumper is set to normal mode. 1. Observe the precautions in "Before You Begin" on page 23. 2. Turn off all peripheral devices connected to the computer. Turn off the computer. Disconnect the computer's power cord from the AC power source (wall outlet or power adapter). 3. Remove the computer cover. 4. Find the configuration jumper block (see Figure 15). 5. Place the jumper on pins 2-3 as shown below. 6. Replace the cover, plug in the computer, turn on the computer, and allow it to boot. 7. The computer starts the Setup program. Setup displays the Maintenance menu. 8. Use the arrow keys to select Clear Passwords. Press and Setup displays a pop-up screen requesting that you confirm clearing the password. Select Yes and press . Setup displays the maintenance menu again. 9. Press to save the current values and exit Setup. 10. Turn off the computer. Disconnect the computer's power cord from the AC power source. 11. Remove the computer cover. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
Intel Desktop Board D525MW Product Guide
40
Figure 15 shows the location of the Desktop Board’s BIOS configuration jumper block.
Table 13. Jumper Settings for the BIOS Setup Program Modes
Jumper
Setting
Mode
Description
Normal (default) (1-2)
The BIOS uses the current configuration and
passwords for booting.
Configure (2-3)
After the Power-On Self-Test (POST) runs, the
BIOS displays the Maintenance Menu.
Use this
menu to clear passwords.
Recovery (None)
The BIOS recovers data from a recovery diskette
in the event of a failed BIOS update.
Clearing Passwords
This procedure assumes that the board is installed in the computer and the
configuration jumper is set to normal mode.
1.
Observe the precautions in "Before You Begin" on page 23.
2.
Turn off all peripheral devices connected to the computer. Turn off the computer.
Disconnect the computer’s power cord from the AC power source (wall outlet or
power adapter).
3.
Remove the computer cover.
4.
Find the configuration jumper block (see Figure 15).
5.
Place the jumper on pins 2-3 as shown below.
6.
Replace the cover, plug in the computer, turn on the computer, and allow it to
boot.
7.
The computer starts the Setup program.
Setup displays the Maintenance menu.
8.
Use the arrow keys to select Clear Passwords.
Press <Enter> and Setup displays a
pop-up screen requesting that you confirm clearing the password.
Select Yes and
press <Enter>.
Setup displays the maintenance menu again.
9.
Press <F10> to save the current values and exit Setup.
10.
Turn off the computer.
Disconnect the computer’s power cord from the AC power
source.
11.
Remove the computer cover.