Intel DX58SO2 English Product Guide - Page 63

Installing the WiFi/Bluetooth* Module in a Desktop Chassis

Get Intel DX58SO2 PDF manuals and user guides View all Intel DX58SO2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Installing and Replacing Desktop Board Components Installing the WiFi/Bluetooth* Module in a Desktop Chassis NOTE The WiFi/Bluetooth*module is supplemental hardware that is included with certain Desktop Boards. Additional WiFi/Bluetooth modules can be ordered online from http://click.intel.com/Desktop_system_parts-0-C97.aspx. Installing the WiFi/Bluetooth module that is shipped with Intel Desktop Board DX58SO2 in your desktop system allows you to connect to wireless networks and Bluetooth peripherals. The recommended installation procedure for a typical desktop chassis is as follows: 1. Observe the precautions in "Before You Begin" on page 31. 2. Make sure that the system is turned off and disconnected from its power source. 3. Remove the plastic cover from an empty 5-1/4 inch drive bay in the chassis bezel (Figure 29, A). 4. Remove the metal filler plate from the internal drive bay (Figure 29, B). 5. Remove the paper backing covering the adhesive on the back of the WiFi/Bluetooth Module and attach the module to the back side of the plastic drive bay cover (Figure 29, C). 6. Connect one end of the USB cable to the connector on the front of the module (Figure 29, D). 7. Reinstall the plastic drive bay cover in the chassis bezel while routing the USB cable into the chassis through the empty drive bay (Figure 29, E). 8. Connect the free end of the USB cable to an unused front panel USB header on the Desktop Board (see Figure 23, G for locations) (Figure 29, F). 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Installing and Replacing Desktop Board Components
63
Installing the WiFi/Bluetooth* Module in a
Desktop Chassis
NOTE
The WiFi/Bluetooth*module is supplemental hardware that is included with certain
Desktop Boards.
Additional WiFi/Bluetooth modules can be ordered online from
.
Installing the WiFi/Bluetooth module that is shipped with Intel Desktop Board
DX58SO2 in your desktop system allows you to connect to wireless networks and
Bluetooth peripherals.
The recommended installation procedure for a typical desktop chassis is as follows:
1.
Observe the precautions in "Before You Begin" on page 31.
2.
Make sure that the system is turned off and disconnected from its power source.
3.
Remove the plastic cover from an empty 5-1/4 inch drive bay in the chassis bezel
(Figure 29, A).
4.
Remove the metal filler plate from the internal drive bay (Figure 29, B).
5.
Remove the paper backing covering the adhesive on the back of the WiFi/Bluetooth
Module and attach the module to the back side of the plastic drive bay cover
(Figure 29, C).
6.
Connect one end of the USB cable to the connector on the front of the module
(Figure 29, D).
7.
Reinstall the plastic drive bay cover in the chassis bezel while routing the USB
cable into the chassis through the empty drive bay (Figure 29, E).
8.
Connect the free end of the USB cable to an unused front panel USB header on the
Desktop Board (see Figure 23, G for locations) (Figure 29, F).