Intel SC5295-E User Guide - Page 91

Installing a Hot Swap Hard Drive

Get Intel SC5295-E PDF manuals and user guides View all Intel SC5295-E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 91 highlights

Hot Swap Drive Cage Upgrade Install Instructions (optional) Installing a Hot Swap Hard Drive Note: The following set of instructions is only applicable if you have replaced the fixed hard drive cage that shipped with your chassis with an optional hot swap SCSI or SATA hard drive cage. If you are replacing a fixed hard drive, see "Removing a Fixed Hard Drive" for instructions. Note: The Entry Server Chassis SC5295-E does not support all hard drives. See "Additional Information and Software"for an Internet link to a list of supported hard drives. 1. Open the drive bay access door. TP01730 Figure 91. Opening Drive Bay Access Door 2. Remove a drive carrier from the hot swap drive cage. Press in on the green latch (see letter "A" in the following figure) at the end of the drive carrier to disengage the drive carrier from the drive cage. Pull out on the black lever (see letter "B") to push the drive carrier partially out of the drive cage. Slide the drive carrier all the way out of the drive cage. Intel® Entry Server Chassis SC5295-E UP/DP/WS/BRP User Guide 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
Hot Swap Drive Cage Upgrade Install Instructions (optional)
Intel® Entry Server Chassis SC5295-E UP/DP/WS/BRP User Guide
73
Installing a Hot Swap Hard Drive
Note:
The following set of instructions is only applicable if you have replaced the fixed hard
drive cage that shipped with your chassis with an optional hot swap SCSI or SATA hard
drive cage. If you are replacing a fixed hard drive, see
“Removing a Fixed Hard Drive”
for instructions.
Note:
The Entry Server Chassis SC5295-E does not support all hard drives. See
“Additional
Information and Software”
for an Internet link to a list of supported hard drives.
1.
Open the drive bay access door.
Figure 91. Opening Drive Bay Access Door
2.
Remove a drive carrier from the hot swap drive cage. Press in on the green latch (see
letter “A” in the following figure) at the end of the drive carrier to disengage the drive
carrier from the drive cage. Pull out on the black lever (see letter “B”) to push the
drive carrier partially out of the drive cage. Slide the drive carrier all the way out of
the drive cage.
TP01730