Intel SE7320SP2 User Guide - Page 42

Diskette Drive Activity Light Does Not Light - front panel

Get Intel SE7320SP2 - 800MHZ Ecc Ddr Xeon PDF manuals and user guides
UPC - 735858168731
View all Intel SE7320SP2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Diskette Drive Activity Light Does Not Light Check the following: ‰ Are the diskette drive's power and signal cables properly installed? ‰ Are all relevant switches and jumpers on the diskette drive set correctly? ‰ Is the diskette drive properly configured? ‰ Is the diskette drive activity light always on? If so, the signal cable may be plugged in incorrectly. If you are using the onboard diskette controller, use the BIOS setup to make sure that "Onboard Floppy" is set to "Enabled." If you are using an add-in diskette controller, make sure that "Onboard Floppy" is set to "Disabled." CD-ROM Drive or DVD-ROM Drive Activity Light Does Not Light Check the following: ‰ Are the CD-ROM/DVD-ROM drive's power and signal cables properly installed? ‰ Are all relevant switches and jumpers on the drive set correctly? ‰ Is the drive properly configured? Cannot Connect to a Server ‰ Make sure the network cable is securely attached to the correct connector at the system back panel. ‰ Try a different network cable. ‰ Make sure you are using the correct and the current drivers. See "Additional Information and Software" for a link to the current drivers. ‰ Make sure the driver is loaded and the protocols are bound. ‰ Make sure the hub port is configured for the same duplex mode as the network controller. ‰ Make sure the correct networking software is installed. ‰ If you are directly connecting two servers (without a hub), you will need a crossover cable. ‰ Check the network controller LEDs next to the NIC connectors. Intel Server Board SE7320SP2 / SE7525GP2 User Guide 42

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
Diskette Drive Activity Light Does Not Light
Check the following:
Are the diskette drive’s power and signal cables properly installed?
Are all relevant switches and jumpers on the diskette drive set correctly?
Is the diskette drive properly configured?
Is the diskette drive activity light always on?
If so, the signal cable may be plugged in
incorrectly.
If you are using the onboard diskette controller, use the BIOS setup to make sure that “Onboard
Floppy” is set to “Enabled.”
If you are using an add-in diskette controller, make sure that
“Onboard Floppy” is set to “Disabled.”
CD-ROM Drive or DVD-ROM Drive Activity Light Does Not Light
Check the following:
Are the CD-ROM/DVD-ROM drive’s power and signal cables properly installed?
Are all relevant switches and jumpers on the drive set correctly?
Is the drive properly configured?
Cannot Connect to a Server
Make sure the network cable is securely attached to the correct connector at the system back
panel.
Try a different network cable.
Make sure you are using the correct and the current drivers. See “
Additional Information and
Software
” for a link to the current drivers.
Make sure the driver is loaded and the protocols are bound.
Make sure the hub port is configured for the same duplex mode as the network controller.
Make sure the correct networking software is installed.
If you are directly connecting two servers (without a hub), you will need a crossover cable.
Check the network controller LEDs next to the NIC connectors.
Intel Server Board SE7320SP2 / SE7525GP2 User Guide
42